Question about 2000 Ford Crown Victoria

1 Answer

1998 Crown Victoria turn signal/flasher

Push the flasher switch, nothing happens. Thereafter, the previously fine turn signals are dead. Took it to Firestone, they said they couldn't figure it out, but on the way home the turn signals were working fine. Short of never trying to turn the flashers on again, which is a very cheap fix, any ideas of what the problem is? -- Charly Coughran ccough@DELETE-TO-RESPOND-UCSD.EDU I have a similar issue, and have a new flasher module, but I can't find where the old one is to replace it. Any ideas?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 50 Answers

Usually the flasher relays are located either under the dash or out under the hood in a small black box along with some other fuses.  You can try swapping the flasher relays with other relays (for example: fuel pump relay, headlight relay, etc...) just as long as they look the same.  If your flashers start working then the relay is your problem and you can go to a local auto parts store and pick up a new one for about $10.

Posted on Jan 31, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Flasher module


I would suggest installing a new flasher module.Not sure of the location.Should be near the fuse panel.

Aug 15, 2014 | 1998 Ford Crown Victoria

2 Answers

No turn signals, everything else works including hazards, took the box out under the dash where i was told the relay would be, and yes theres like 6 relays but they dont come off the board....


Actually there is a relay however it is not an individual part. The turn signal relay and the hazard relay are in the LCM (Lighting Control Module). This is expensive to replace however you should test the multi-function turn signal switch first as I am having the exact same problem with my 95 Crown Victoria LX. If you go to any parts store they will tell you that it is just a relay and sell you one for the newer Crown Victoria models. However in the 95 to about 2002 models they employed the bad idea of the LCM.Good luck.

Jul 26, 2011 | 1996 Ford Crown Victoria

1 Answer

My 1993 crown victoria's signals are not working, my headlights and taillights all work. what is wrong and how do i fix it? i dont have alot of money and need to know how to fix this on my own.


CHECK TURN SIGNAL FUSE IN THE FUSE BOX LOWER LEFT SIDE OF THE INSTRUMENT PANEL.IF FUSE OKAY PROBLEM COULD BE THE FLASHER IN THE FUSE BOX ITS A LARGE ROUND METAL TIN LOOKING FUSE.YOU SEE IT IN THE INTERIOR FUSE BOX.IF FLASHER GOOD.TURN SIGNAL SWITCH COULD BE FAULTY.SHAKE TURN SIGNAL SWITCH WIRES CHECK FOR SHORTS.

Nov 21, 2010 | 1993 Ford Crown Victoria

1 Answer

My signal lights dont work on my 1995 ford crown victoria i need to know what fuse to change


turn signals usually have a flasher relay, you might also look at the switch in teh steering column. if the emergency flashers still work, swap the flashers, to see if that fixes the flashers.

Sep 03, 2010 | 1995 Ford Crown Victoria

1 Answer

Turn signals on my 99 crown Victoria are not working, i tried the fuse all ready


If all other lights are working properly (brakes, hazards and tail lights) there is a good possibility that it is a flasher unit. The flasher unit is usually near or in the fuse block and is usually a small round about an inch in diameter - can be plastic or metal covered. Grasp it firmly and pull straight out on it. There are 2 contacts at a 90° angle that fit into the board. A new unit should be under $10. To reinstall it - just align the contacts with the slot and push it firmly back into place. On most vehicles the hazard flasher unit is the same device but a separate unit. If you turn on the hazard switch and those lights are working you will be able to hear a click as it turns on and off. Once installed - activate the turn signals with the key on to see if it clicks.

Dec 17, 2009 | 1999 Ford Crown Victoria

1 Answer

Turn signals, hazard flashers, and brake lights not working on 1996 crown vic. pushed in fuse and worked for minute until hood was shut then went out again. Also took in circuit breaker and had checked....


well makes no sense turnsignals are on ignition switch fed fuse and brake lights are on 24 hour fuse.. to me sounds like bad turn switch... it handles turn signals also hazzards. and brake lights have to go through the turn switch also... it is common problem.. combination switch is what they call it.. not hard to replace either....let me know

Aug 31, 2009 | 1996 Ford Crown Victoria

1 Answer

97 crown vic turn signals , emergency flashers and brake lights d


have the multifunction switch checked and the flasher.

Jun 15, 2009 | 1997 Ford Crown Victoria

2 Answers

No turn signals or emergency blinkers


Sounds like a multifunction switch, work the emergency flasher button up and down a few times, then attempt to work the turn signals if the signals work then you will need a multifunction switch.

Apr 30, 2009 | 1997 Ford Crown Victoria

1 Answer

Hazzard Lights on 1998 Ford Crown Victoria won't work


The hazards are on a seperate fuse to the indicators, on the inside of the fuse box cover it will tell you which fuse it is, simply replace it with one of the same rating and your hazards should work, if not come back to me

Mar 16, 2009 | 1998 Ford Crown Victoria

Not finding what you are looking for?
2000 Ford Crown Victoria Logo

814 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...