Question about 2004 Dodge Stratus

Open Question

Where is the oil pressure sending unit on the 2.7 located?

Where is the oil pressure sending unit on the 2.7 located

Posted by on

  • paconarvleon Feb 23, 2009

    i changed the thermostat and the car started but then the car turned off and the engine oil pressure light came on and the car well not start

  • bofree Apr 15, 2009

    I have a 2005 Stratus RT and the oil light comes on at idle or low RPM. I went to NAPA and purchased a sending unit so I would know what it looked like. Got under the car and could not find location so guess I am going to have to go to a dealer to get it replaced.

×

5 Suggested Answers

  • 1 Answer

SOURCE: Pontiac Bonneville(2000) oil pressure sending unit

The oil pressure sending unit is located behind the oil filter, Threaded into an aluminunm housing. It has wiring that plugs into the sending unit. The oil filter has to be removed and you will need a deep well socket and a 6 inch extension. Change the oil and the sending unit together.

Posted on Feb 02, 2009

SOURCE: oil sending unit

I have heard sludge buildup can be an issue with Dodge engines in Durangos. Make sure sludge is not blocking oil flow and reducing pressure.

Posted on Nov 07, 2008

  • 31 Answers

SOURCE: Can not find oil pressure sending unit on engine.

yes it will be on the lower part of the engine block. i believ on passenger side.

Posted on Jan 18, 2009

farroutideas
  • 78 Answers

SOURCE: oil pressure sending unit

Hi there;

Your looking foer the oil pressure sensor on the 2004 8.1L.
You will find it located directly behind the EGR valve threaded into the block just to the drivers side of the center bolt for the transmission to block connection.

Thanks
Farrout!

Posted on Mar 17, 2009

michigan man
  • 3533 Answers

SOURCE: Where is the oil sending unit on a 2002 dodge ram 1500 4.7 L?

it normally is located near the oil filter it looks like a little plug with a wire on it

Posted on Apr 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Change oil sending unit 04 tahoe


It is located on rear of engine back by the distributor use to be. see attached pic
25576498-orvua4poo00lqzajd5seke1u-5-0.gif

Mar 15, 2015 | 2004 Chevrolet Tahoe

1 Answer

Where is the oil pressure sending unit located in a '01 dodge dakota, 4.7 eng.?


go to CTC and buy a service manual for 2001 dodge Dakota 4.7 litre engine there will be 2 oil pressure sending units one that is for the gauges in the dash and the other for the oil pressure sending unit mounted on engine

Feb 12, 2015 | Dodge Cars & Trucks

2 Answers

Location of oil sending unit on 1990 ranger 2.9


Here's a link to your oil pressure switch,here's the part.As you can see there are 2 types,one for light and one for gauge.
  • When the oil pressure is either high or low it will either turn the oil light "on" in the dash or move the gauge to the extremes
  • Undetected high or low oil pressure can result in internal engine damage and/or gasket leakage

Apr 17, 2013 | Cars & Trucks

1 Answer

I need to replace the oil sender switch on my 2002 Buick La Sabre


first need to buy oil pressure sending unit 3/8 deep socket remove oil pressure sending unit you need teflon tap sealer for oil sending unit threads.okay to replace oil pressure sending unit.you need safe raise support vechicle locate oil pressure sending unit next to the oil filter.disconnect oil pressure sending unit wire connector then use oil pressure sending unit 3/8 socket remove the sending unit.then take new oil pressure sending unit use teflon tape white plumbers tape or use thread sealer apply to the oil pressure sending unit threads then install new oil pressure sending unit and reconnect electrical connector to sending unit.then crank engine check for oil leak if all is good lower vechicle back to ground wait several minutes check engine oil level.you good to roll.

Feb 09, 2013 | 2002 Buick LeSabre

1 Answer

I have a 99 Ford F150 with a 5.4. It will start and run fine, no codes. After 2 minutes of running the oil pressure goes to zero. Shut off the engine and restart the oil pressure will go up to normal for...


Start by verifying the oil pressure sending unit. It is quite common for a bad sensor to act erratically, such as you have described. Acquire an oil pressure gauge and install it in an appropriate location, perhaps in place of the oil sending unit if a more convenient location is not available, and run the engine. Observe the pressure on the test gauge at various RPM and over a period of several minutes as the engine warms. If pressure on the gauge is good, then you have a problem either with the oil pressure sending unit, in the circuitry, or instrument panel gauge. However, the problem is most likely the sending unit. Note: the sending unit often requires a special socket, which may be obtained at any auto parts store. Also, if you don't own a test gauge or unwilling to purchase, many auto parts stores now rent tools, others even loan tools provided an adequate security deposit is made.

Jun 19, 2010 | 1999 Ford F150 Regular Cab

1 Answer

Where is the oil pressure sending unit located on a 2000 jeep grand cherokee 4.0 liter


Removal & Installation
  1. Disconnect the negative cable from the battery.
  2. Raise vehicle on hoist.
  3. Remove front splash shield.
  4. Disconnect oil pressure sender connector (4).
  5. Remove the pressure sender (2).
6eaedba.gif
Oil pressure sending unit


To install:
  1. Install oil pressure sender.
  2. Connect oil pressure sender wire.
  3. Install front splash shield.
  4. Lower vehicle.
  5. Connect the negative battery cable.

Jan 12, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Where is the oil pressure sensor located


Oil pressure switch or oil pressure sending unit.most cars have both.If it has one wire it is an oil pressure sending unit. if it has a plug with 2 or more wires it is an oil pressure switch and sends a signal to the inboard computer. Remove the wire either a nut or usually a plug.some sending units take a special socket but if you can get a wrench on it turn it counter clock wise and unscrew it. When you get the new one it will have a red material on the threads, this is a sealant.thread the new switch snug and put you plug back on.The sending unit or oil pressure switch is located next to the oil filter. Good luck and keep me posted, Auto Zone will have this part and also have the step by step instructions for you to get the job done.

Nov 17, 2009 | 1996 Nissan Sentra

3 Answers

Where is the oil pressure sending unit located?


The pressure sending unit is located on the passenger side rear of the engine just above and slightly to the left of the filter and filter housing.

May 10, 2009 | 2000 Buick LeSabre

1 Answer

No oil pressure


Sounds like sending unit, should be located by where the oil filter is.

Feb 26, 2009 | 1996 Jeep Grand Cherokee

2 Answers

Pontiac Bonneville(2000) oil pressure sending unit


The oil pressure sending unit is located behind the oil filter, Threaded into an aluminunm housing. It has wiring that plugs into the sending unit. The oil filter has to be removed and you will need a deep well socket and a 6 inch extension. Change the oil and the sending unit together.

Jan 24, 2009 | 2000 Pontiac Bonneville

Not finding what you are looking for?
2004 Dodge Stratus Logo

Related Topics:

893 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...