Question about 1994 Chevrolet Camaro

1 Answer

1994 chevy camaro 3.4manual 5 speed

I put all new clutch system and had flywheel refaced new slave cylinder new clutch master cylinder cant get the clutch system to bleed no peddle no bleeder screw how can i get it to work im lost have big problem no clutch pressure been pumping peddle all week and still no pressure

Posted by on

  • Roberta Smith
    Roberta Smith May 11, 2010

    when they resurfaced the flywheel did they take too much off... check the specs on that

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,674 Answers

You may want to read bleeding instruction at this link, it may shed some light.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800b886d

Posted on Jan 31, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just replaced full clutch kit in a 1999 Hyundai Xcel X3, including slave cylinder and flywheel reface. And its slipping as bad or worse than with old clutch, Any ideas


maybe the original problem was the clutch master cylinder
it the compensating port is blocked , it holds the clutch pressure plate off and slips the clutch
not the problem then did the clutch fork( release lever go back in the right wat

Feb 01, 2017 | Hyundai Cars & Trucks

1 Answer

Adjust the clutch linkage on a pontiac 2002 trans am 6 speed


How to adjust clutch??? 95 bird. - Fourth Generation Pontiac ...

www.firebirdnation.com/forums/.../65178-how-to-adjust-clutch-95-bird/
Dec 5, 2008 - posted in Fourth Generation Pontiac Firebird (1993 - 2002): I have ...Year: 2000; Make: Pontiac; Model: TRANS AM; Engine: 5.7L LS1; Transmission: MANUAL 6 SPEED T-56 ... Have you looked at your clutch master cylinder. Throttle is sticking after acceleration - Fourth Generation ...
Oct 7, 2011
1 Problem / Few questions - Fourth Generation Pontiac Firebird ...
Mar 26, 2010
Firebird Technical Service Bulletins - Fourth Generation Pontiac ...
Jul 5, 2006
TECH ARTICLE MASTER INDEX Look Here - Firebird Nation
Aug 18, 2004
More results from www.firebirdnation.com

How to Install Clutch 98-02 LS1 F-Body Part 1 of 2 - YouTube

? 12:31
www.youtube.com/watch?v=4BCHu2BwBMs

Apr 12, 2013 - Uploaded by MapleBoarder78
Part one of installing a new clutch on my 2000 Trans Am. Part 2 will include installation ... How to Master Cylinder Install and Drill Mod (LS1 F-Body) - Duration: ... 6:28. Removal and Servicing ofClutch Master Cylinder to Slave Cylinder ... LS1 98-02 Chevy Camaro Z28 SS Pontiac Firebird Trans Am F-Body ...

Nov 02, 2015 | Pontiac Cars & Trucks

1 Answer

1990 chevy silverado wont disingage new clutch and pressureplate...master cylinder and slave cylinders are new and have been bleed extensively...cant figure out why it wont fully disingage


this is really a simple problem to fix. Pull the gear box and turn the clutch pale around because the plate hub centre is hitting on the flywheel stud heads . The clutch plate only go in one way.

Jul 17, 2014 | Cars & Trucks

2 Answers

Clutch seems to be slipping I put everything in new


Sounds like bad clutch but that should have been replaced when fly wheel fly wheel worked on.

Jan 15, 2013 | 1992 Jeep Wrangler

1 Answer

94 Chevy 2500 Clutch Engagement?


You probably have a hydraulic clutch. A hydraulic clutch has both a master and a slave cylinder. The slave cylinder engages/disengages the clutch plate. You might be low on clutch fluid in the master cylinder, or the system may need to bled similar to bleeding brakes. Worst case is you need a new clutch, pressure plate, and throwout bearing. They should all be replaced when doing a clutch job.

Aug 23, 2012 | Cars & Trucks

2 Answers

I changed out my slave and master cylinder in a 96 chevy camaro Z28. After doing so pushed down on the clutch to let out all the air bubbles from the new brake fluid. But the cluth is still soft, it has...


put a bar behind the clutch operating arm ,slacken bleed nipple on the slave then pull the bar back so it pushes the slave piston in.tighten bleed then release pressure on the bar ,and repeat a few times this should do it

Nov 20, 2009 | 1996 Chevrolet Camaro

1 Answer

I press my clutch and get no resistance and cant get into any gear? 2003 gmc sierra 8.1 4x4 2500hd 5 speed


Check fluid level in clutch master cylinder, if fluid is full then bleed clutch system.

If you still have no pedal resistance you will need a new master or slave cylinder for the clutch.

1c6f931.jpg

Oct 30, 2009 | 2003 GMC Sierra 2500HD

1 Answer

Cant shift? reverse grinds? and pressure in clutch is low


What you describe sounds very much like the clutch is failing to disengage.
Fluid level being fine and no leaks under the car is good, but doesnt mean there isnt something wrong with either the master cylinder, slave cylinder, or the associated parts.

Highly unlikely there is a fault with the flywheel or clutch as failures with these would normally give no drive in any gear.

Oct 03, 2009 | 1994 Chevrolet Camaro

1 Answer

Clutch pedal stays 2 the floor on a hydralic clutch system on a 2000 camaro v8. clutch master cylinder is new also slave cylinder and clutch and pressure plate


Did you bleed the system? When you replace the the master and/or slave cylinder you have to bleed the system just as you would with brakes. There is a bleed screw on the slave cylinder. Open the bleed screw, have a helper depress and hold the clutch pedal down.Tighten the bleed screw, then release clutch. Repeat this procedure until you have removed all air from the system and the clutch pedal is firm. Keep an eye on the fluid level to avoid sucking air into the system. If you have done this, remember there is a possibility that the master or slave cylinder is defective.

Sep 06, 2009 | 2000 Chevrolet Camaro

1 Answer

2002 dodge diesel 2500 5 Speed....... Clutch will


if master cylinder and slave cylinder.is good and have brake fluid is in system and no leaks.problem is in the clutch and pressure plate.

Jun 10, 2009 | 2001 Dodge Ram 2500 Truck

Not finding what you are looking for?
1994 Chevrolet Camaro Logo

580 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...