Question about 2006 Toyota ECHO

2 Answers



Posted by on


2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

1. In the back of the headlight, you should see a rubber insert and a plug going in that's in the shape of a cube.
FRONT PILOT LAMP 12V 5W TOYOTA YARIS 2001 - headlight.jpg

2. Disconnect the cube shaped plug by pulling it out. There is grease on there so have a towel to wipe your hands just in case you don't want your hands dirty.

3. Remove the rubber insert simply by tugging it out. It's a lot easier than you think so don't tug that hard and hurt your hands. Now, after the rubber insert is removed, this is the trickiest part. I tried to take the bestest picture I can. In the picture below, you see 3 metal stick sticking out and to the right a bit, you see a little tab. What you need to do is push that tab in, towards the headlight direction, and unhook the bulb that's connecting to it. Give it a few try and you'll know what I'FRONT PILOT LAMP 12V 5W TOYOTA YARIS 2001 - headlight3.jpgt.

4. Now, after the hard work of getting the bulbs out, remove them carefully from the car. Replace the bulbs you would like on back inside the bulb. The type of bulbs the Echo uses are H4. I bought some off ebay for around 9.99. Xenon HID, they give off a white light with a dark bluish tint to it. Putting back the bulb is easy, just put the bulb in, hook the switch (tab thingy) back on and reconnect everything. You might want to put some grease on the new bulbs though. GreaseFRONT PILOT LAMP 12V 5W TOYOTA YARIS 2001 - lightbulbs.jpge the 3 metal stick sticks out.

Posted on May 19, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

Should be a quarter turn either way to undo it.


Please rate this solution... thanks

Posted on Jan 31, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Change indicator bulb front

Under the hood on the headlight bulb housing you will see what looks like a gray colored fin. That is the bulb holder. Space could be tight. Grab and twist to remove the holder. Many times it's the holder and not the bulb. If you change the bulb or holder do both sides at the same time, it's cheap enough.

Apr 03, 2014 | 2001 Audi A4

2 Answers

How to replace a front side marker bulb on a 2007 Toyota Yaris Sedan

You don't need a dealer for much of anything

All of todays vehicles require removing the lamp
assembly or housings,front or rear, of any vehicle,to
take out the lamps/bulbs

If you open the hood you will find screws that hold it in place

May not be an easy job, but that's the junk were sold

Sep 05, 2012 | 2007 Toyota Yaris

1 Answer

How to replace bulb in front bumper turn signal housing 1995 jag xj6

  • Identify the blown bulb. Note that if a headlight bulb has blown, the dip beam is on the outside and the high beam is on the inside. Turn off the ignition switch and light switches.

  • Open the hood and replace any blown headlight bulbs. Press the plastic spring clips and remove the bulb holder from the assembly. Pull the bulb out of the bulb holder and replace it with a new bulb. It only fits one way. Be sure not to touch the bulb's glass. Replace any parking lights at the same time, they are in the headlamp unit too.

  • Remove the front turn signal light unit in the bumper to change the turn signal bulb. Push gently on the inside edge and insert a blade between the bumper and the lens at the outside edge. Compress the spring and remove the lens. Fit a new lamp by inserting it into the plug. The side marker light is changed using a similar process.

  • Open the trunk to replace the rear fog light, stop light, tail light, reversing light and turn signal light. Remove the rear light cover and turn the bulb holder fastener 90 degrees counter clockwise. Remove the expired bulb, fit a new one and replace the parts, turning the bulb holder clockwise.

  • Thanks..

    May 21, 2011 | 1995 Jaguar XJ6

    2 Answers

    I have a 97 Mercury Montaineer and i need to replace the brake light bulb, and dont know how to..can someone tell me how

    Please don't forget to rate....thanks!


    Exploded view of the rear light assembly used on the Explorer/Mountaineer models


    The Explorer/Mountaineer models only use two upper lens retaining screws, the bottom use barbed push pins

    1. Remove the 2 (Explorer/Mountaineer models) or 4 (Ranger models) screws retaining the lamp assembly to the vehicle.
    2. Remove the lamp assembly from the vehicle by pulling it outward. On the Explorer/Mountaineer models, make sure the 2 barbed retainers at the bottom of the assembly release.


    Pull the lens assembly out from the vehicle body to access the bulb sockets


    Grasp the bulb socket then twist and pull it out of the lens assembly


    Remove the bulb from the socket by pulling it straight out

    1. Remove the lamp sockets from the lens housing by twisting it, then pulling outward.
    2. Remove the bulb from the socket by pulling it straight outward.

    To install:

    1. Install the bulb into the lamp socket.
    2. Install the lamp socket to the lens and twist it to lock it in position.
    3. Position the lens assembly to the body. On Explorer/Mountaineer models, ensure that the barbed retainers are aligned with their mounting clips, and press the assembly until fully seated.
    4. Install the lens assembly retaining screws (four screws used on the Ranger and 2 on the Explorer/Mountaineer).
    5. Check the operation of the lights.
    // // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 35; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

    Jan 19, 2011 | 1997 Mercury Mountaineer

    2 Answers

    How do I replace parking light on front passenger side

    Try to look behind the lens for the parking light for a socket that can be twisted out and unlocked from the back of the lens. Replace the bulb which may be a push in type or twist on type.

    When I looked up information on Chilton and Autozone, I couldn't find information on it, unfortunately.

    Nov 03, 2010 | 2007 Nissan Sentra 2.0 SL Sedan

    1 Answer

    No revers lights

    REMOVAL & INSTALLATION 1988–91 R/V Series
    1. Remove the lens-to-housing attaching screws. Remove the lens.
    2. Replace the bulb(s).
    3. Installation is the reverse of removal.
    Except 1988–91 R/V Series Fig. 1: Remove the lamp assembly retaining screws 87986p17.jpg
    Fig. 2: Pull the lamp assembly from the truck 87986p18.jpg
    1. Lower the tailgate.
    2. Remove the lamp assembly retaining screws.
    3. Pull the lamp assembly from the truck and disconnect the wiring.
    4. Remove the bulb holder fasteners.
    5. Remove the bulb(s) from the lamp.
    6. Install the bulb, connect the wiring and install the lamp. Fig. 3: Disengage the electrical connection 87986p19.jpg
      Fig. 4: Unfasten the bulb holder retainers 87986p20.jpg
      Fig. 5: Remove the bulb holder 87986p21.jpg
      Fig. 6: Pull this type of bulb from the socket 87986p22.jpg
    prev.gif next.gif

    Sep 03, 2010 | 1994 Chevrolet Suburban

    1 Answer

    2004 yaris how do you change headlight bulb passenger side as there is no room for your hands to get in

    to change passenger side headlight bulb,on 04 plate yaris, remove bulb cover at rear of lamp,take off fuse box,although this only gives you slightly more room,and have someone with small hands,replace bulb,as it is nearly impossible if you have large hands.It is awkward but can be done,EVENTUALLY.

    Feb 05, 2010 | 2007 Toyota Yaris

    2 Answers

    How to change brake lights on my 2007 toyota yaris

    on either side of the boot interior, there are what look like air vents. these clip out from the top (with a flat screwdriver) you then unbolt the light unit, pull it out. the bulb holder then unclips easily.

    Jul 13, 2009 | 2007 Toyota Yaris

    1 Answer

    How do you replace a headlight on a 1999 Toyota Rav 4?

    Do you mean the entire headlight assembly or just the bulb?
    If it's the entire headlamp look at the new one to see where the fastening points are, the grill may have to be removed and also the parking lamp lens, if it's just the bulb it's easy Open your hood look at the backof the headlight assembly and twist the bulb holder ring to release it. Good Luck To You

    Jul 09, 2009 | 1997 Toyota 4Runner

    1 Answer

    How to replace Marker lamp in 1999 Toyota Corolla

    Open the hood. Observe the area above the right headlamp, close to the fender. You will see a phillips screw that holds a plastic tab. Remove the phillips screw. After removing the screw, pull the marker lamp assembly towards you. It may be real tight, if it has never been removed before. You need to pull the light assembly out of 2 retention sockets behind the marker lamp. Rotate the bulb socket to get to the bulb, replace the bulb, & slide it back in.Easy job.

    Oct 21, 2008 | 1998 Toyota Corolla

    Not finding what you are looking for?
    2006 Toyota ECHO Logo

    255 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts


    Level 3 Expert

    78257 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8836 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides