Question about 1991 Dodge Stealth

1 Answer

One turbo went out on the 91 stealth should i replace both or just one

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,990 Answers

Just the One that is out should be Just fine on this Car. Please Rate My Response! Thanks!

Posted on Jan 31, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Replacing serpentine belt 91 stealth non turbo 3.0

take picture of how the belt runs over and around
the belt driven parts first
or have the correct layout diagram

find the tension pully
pivot it in the right direction
that take the tension off the old belt
and belt will fall away
fitting...its a bit tougher becasue its a new belt
pivot the tensior pully all the way to its max so th enew serp belt will fit

may not bee the same layout but is the 93 stealth
serp belt


May 29, 2016 | Cars & Trucks

1 Answer

I was driving my manual 91 dodge stealth home when i went to shift into 4th gear the clutch pedal went all the way to the floor and stuck and now it doesnt like to go into gear with the clutch in but it...

Clutch disk or pressure plate or both are worn out, and I would replace the throw out bearing. You can buy a kit at autozone or kragen that has everything all together 100-200 dollars.

Aug 10, 2013 | 1991 Dodge Stealth

1 Answer

I have a 92 dodge stealth sohc when i got it it had fuel issues i replaced fuel filter, spark plugs, distributer cap and roter. Seemed to run fine after that but now it overheats and problems start over. I...

I owned a 91 model--glad you have the sohc as the dohc has real problems.

some general thoughts:

The relay is possible but does the electric fan come on? If it does not after 10 minutes it will overheat.

Saw two where water pump caused same issue.

Check for possible head gasket leaking(compression tested?)

Another valuable resource I have used is the Socal 3S club located in the LA area of California---they have a online forum with areas for problems and solutions---free to join and they have several segments for parts and problems and general back and forth.

Again my experience here is based on owning both a SOHC and a Twin Turbo made in 91-----not like working on a ford...........

Let me know if I can help in any way----you are more likely to get good help from one of the many forums dedicated to these cars than here.

May 17, 2012 | 1992 Dodge Stealth

1 Answer

Where is a fuel pump relay located on a 1993 dodge stealth non turbo

the fuel pump relay on a 91 to 93 dodge stealth base and es models is in the passenger area on the passanger side of the car there a lil kick panel held by one screw behind a black cap pull the panel of and its right behind it.. its a gold box with wire harness connected at bottom. its a 2 part relay that controls ur fuel pump and engine managment system. email me at if u would like a pic of were it is at

Oct 23, 2010 | 1993 Dodge Stealth

1 Answer

How do i obtain original computer # for 1992 dodge stealth sohc

if you have a SOHC engine 92 stealth from California the number will be ;MD153355
SOHC Federal emission ECU number will be ;MD153354 .
DOHC , AWD , Turbo Cali emissions ; MD159965
DOHC , AWD ,Turbo federal emmissions ;MD159966
DOHC non-turbo Calif ;MD159962
DOHC non-turbo fed. ; MD159963

Sep 29, 2010 | 1992 Dodge Stealth

1 Answer

Witch timing marks do I use for my dohc 91 dodge stealth?

I don't know what you got there, but, the marks are just dots, or little arrows, they have to line up or else. I don't think the cam can go in but one way, all 4 valves opening at once doesn't make sense to me but I'll check it out.

Mar 06, 2010 | 1991 Dodge Stealth

1 Answer

91 dodge stealth will start and stop. Changed the fuel pump and computer chip. Now what?

Have you checked or replaced the fuel filter? Sometimes that can be the problem as well because your fuel filter could be clogged.

Jan 28, 2010 | 1991 Dodge Stealth

1 Answer

Timing belt replace on 1991 dodge stealth 3.0 24valve non turbo diagram

My apologies for the delayed response. I am going back and answering questions that were never answered.
Click on the following Link. It has all the Diagrams for the Timing Belt you will need.
Before Clicking, let me know if this helped.
Again my sincerest apologies,,..

Jan 12, 2010 | 1991 Dodge Stealth

1 Answer

91 stealth dohc, w/o turbo. Car starts, runs fine for 10 min, dies. Won't start.After a while will start again. Changed fuel filter, maf, capacitor in ecu. (length of time running has dropped from 60miles...

The main computer (ECU) is directly behind the radio console. Pull carpet back on left and right sides of console. It is not the 'box' lying flat (trans comp). You should be able to take the ECU out w/o removing the radio.

Jul 19, 2008 | 1992 Dodge Stealth

Not finding what you are looking for?
1991 Dodge Stealth Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides