Question about 1990 Nissan Hardbody King Cab

1 Answer

Replacing brake pads on a 1998 Nissan Hardody

Replacing brake pads on a ... nissan 2.4 Hardbody.. model 1998

Thanks
Pieter

Posted by on

  • Anonymous Mar 26, 2014

    replaced linings. Now not sure where the springs go?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 188 Answers

One bolt to remove, and the caliper will swing out of the way. Get a C-clamp and loosen the brake bleederand compress the piston back into the caliper. Tighten the bleeded screw & take the clamp back off after the bleeded screw is tighten!!!! When U purchase the pads, make sure the you get the jelley type, RTV the you put on the metal of the pad backing to keep the brakes from squeeling when you apply the brakes going down the road, Install the pads, and put bolt back on. Your finish, brake job done.

Posted on Jan 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Nissan hardbody 3.0td loses power and dtc code 42 comes up


Problem with 1998 Honda Civic Nissan hardbody 3.0td loses power and dtc code 42 must be old nissan as 98 civics use OBD2 codes.
what year, Nissan, and is this Turbo Diesel, if yes, get the FSM
its complex.ever heard of that , FSM
the factory service manual, all cars have it.

Aug 22, 2013 | 1998 Honda Civic

2 Answers

I have 89 nissan hardbody 4x4 SE...can i use an older or new model to get the parts i need when the 89 is not available


Well I know the blinkers won't fit from 90-97 cuz they are more wider and other than that you change anything from 86-97

Jul 12, 2011 | 1989 Nissan Hardbody King

1 Answer

Nissan Terrano Japanese import 1995 free manual


might have a job here ,manual unless you understand japanese ,also you might have a job re-registering because it will not have a europeon certificate of homoglonation number.

Apr 07, 2010 | 1990 Nissan Hardbody King Cab

1 Answer

Nissan Premira 2002, european spec. When replacing brakes pads w/ABS, are there any adjustments required or resetting procedures? My email is address harrisleon53@yahoo.com


The vehicle being worked on was jacked up and supported by sturdy jack - stands. All four wheels were removed to access disc brake assemblies. Tools utilized (1) C clamp for the front caliber to press piston back in it bore and (2) a special tool for the rear to return caliber back in it bore. Replaced pads and all pertinent hardware, torque all fasteners to specification and wheel assemblies. Road tested vehicle and checked for noise and rattles. So thanks for the tip that was given and I wish you and your staff a nice sunday.


"Hank"

Jul 18, 2009 | 2002 Nissan Quest

1 Answer

Need cylinder head bolts torque settings for nissan 3.2d


what nissan model do you need the head torques for

May 01, 2009 | 1990 Nissan Hardbody King Cab

1 Answer

I need to remove the front rotors


here's a good instructional video on replacing the rotors... any more information you need feel free to ask.

http://www.monkeysee.com/play/11914-how-to-replace-brakes-brake-pads-and-rotors

Please take a moment to rate this solution.. thanks

Apr 16, 2009 | 1997 Nissan Pathfinder

1 Answer

Sometimes it runs ok,then every now and then it stutters and sometimes there is no fuel getting through,its a nissan micra 1993 model


My 93 nissan truck had a similar problem with stuttering that was fixed by replacing the fuel pump. Hitting a bump or even slamming the tailgate would cause it to start.

Jul 14, 2008 | 1990 Nissan Hardbody King Cab

1 Answer

Replacing front brake pads on Nissan 2000 Hardbody model 2000


pull the wheels off .undo brake fluid cover .On the back of rotor there are 2 long pins that you have to remove to pull the caliper off.After the caliper is off pull the old brake pads off ,remembering which way they came off.Now with either a large C-Clamp ,or large channell lock pliers compress the large round metal part that pushes against the back of brake pad.The idea is this,your new pads wont fit on the rotor unless you compress this part ALL the way down,that is why you took the fluid cover off earlier,so the back pressure can go back into the brake fluid reservoir .Once you have this part pushed in ,install the 2 pads and put the whole thing back over and on the rotor .Last of all put the long pins back on tight, put the wheel on ,and now do the other side.............Good luck ! Patience is Key !!
Please rate this !! Thank You!

Jun 10, 2008 | 1997 Nissan Pickup

Not finding what you are looking for?
1990 Nissan Hardbody King Cab Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...