Question about 2001 Chrysler Town & Country

1 Answer

Heater blowing cold

2001 Town and Country the heat fan works on all levels. However, the air does not get warm. I turn the switch and received 2 error codes P-1684 and P-1682 but I don't know where to look them up.

Posted by on

  • scubad70 Feb 03, 2009

    It turns out that the radiator was low on coolant. Filled it up and now it works great.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 373 Answers

I hope that is not a head gasket
I had to do that to mine

Posted on Jan 31, 2009

  • jim beckwith Feb 03, 2009

    great man that is a good fix

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The heater in my 2005 chrysler town and country mini van blows heat then turns cold


Make sure your radiator is full of coolant, if it is low the heater core cant get enough hot coolant in it to keep the air warm. If that's not the poroblem it could be a problem with your air exchanger that switches from hot to cold which could be a vaccume line leak. But I bet you're just low on Coolant.

Oct 17, 2013 | 2005 Chrysler Town & Country

2 Answers

2006 town and country fan blows cold air all the time


Change the heating core. Sometimes dificult. Located under the dash.

Dec 31, 2012 | 2006 Chrysler Town & Country

1 Answer

No heat air is blowing cold


First you have to identify what causes the problem.
To do this you have to:
1) When engine is cold check the level of coolant. If it is low fill it up.
2) Start engine and check if engine reaches regular temperature. If your engine is not heated enough it means your thermostat does not work properly and should be replaced.
3) If engine temperature is normal, then check the temperature of pipes that go to/from heater core. These pipes are located up the fire wall (easier access is from the passenger side). If pipe/pipes are cold (even engine is worm) it means you heater core is plugged and should be flushed. Keep in mind, flushing the whole cooling system is different from flushing heater core.
4) If pipe/pipes are hot/warm, turn off the fan, switch controller to the hot position, wait for 3-4 minutes and turn on the fan. Note if the cold air blows first or warm air blows first but it cools down in 5-10 seconds. If the air blows cold than it is most probably the problem with blend door or blend door actuator.
5) If air blows warm first and then cools down, then while running engine and remaining the transmission in PARKING position, press on the gas pedal until your engine reaches 3,000 RPM. Check if your heater blows warm/hot air. If it does, then your water pump does not work properly and should be replaced. If the air still cold, I would suggest to flush the heater core.

Oct 22, 2009 | 1998 Ford Taurus

1 Answer

MY 1998 FOR TARUS HEATER WILL NOT WORK.WAS DRIVING


It is most probably the problem with blend door or blend door actuator. But just in case I would suggest to follow the entire procedure:

First you have to identify what causes the problem.
To do this you have to:
1) When engine is cold check the level of coolant. If it is low fill it up.
2) Start engine and check if engine reaches regular temperature. If your engine is not heated enough it means your thermostat does not work properly and should be replaced
3) If engine temperature is normal, then check the temperature of pipes that go to/from heater core. These pipes are located up the fire wall (easier access is from the passenger side). If pipe/pipes are cold (even engine is warm) it means you heater core is plugged and should be flushed. Keep in mind, flushing the whole cooling system is different from flushing heater core.
4) If pipe/pipes are hot/warm, turn off the fan, switch controller to the hot position, wait for 3-4 minutes and turn on the fan. Note if the cold air blows first or warm air blows first but it cools down in 5-10 seconds. If the air blows cold than it is most probably the problem with blend door or blend door actuator.
5) If air blows warm first and then cools down, then while running engine and remaining the transmission in PARKING position, press on the gas pedal until your engine reaches 3,000 RPM. Check if your heater blows warm/hot air. If it does, then your water pump does not work properly and should be replaced. If the air still cold, I would suggest flushing the heater core.

Oct 17, 2009 | 1998 Ford Taurus

1 Answer

Heater not working


First you have to identify what causes the problem.
To do this you have to:
1) When engine is cold check the level of coolant. If it is low fill it up.
2) Start engine and check if engine reaches regular temperature. If your engine is not heated enough it means your thermostat does not work properly and should be replaced.
3) If engine temperature is normal, then check the temperature of pipes that go to/from heater core. These pipes are located up the fire wall (easier access is from the passenger side). If pipe/pipes are cold (even engine is warm) it means you heater core is plugged and should be flushed. Keep in mind, flushing the whole cooling system is different from flushing heater core.
4) If pipe/pipes are hot/warm, turn off the fan, switch controller to the hot position, wait for 3-4 minutes and turn on the fan. Note if the cold air blows first or warm air blows first but it cools down in 5-10 seconds. If the air blows cold than it is most probably the problem with blend door or blend door actuator.
5) If air blows warm first and then cools down, then while running engine and remaining the transmission in PARKING position, press on the gas pedal until your engine reaches 3,000 RPM. Check if your heater blows warm/hot air. If it does, then your water pump does not work properly and should be replaced. If the air still cold, I would suggest flushing the heater core.

Oct 17, 2009 | 1998 Ford Taurus

1 Answer

CHRYSLER TOWN & COUNTRY 2003 HEATER PROBLEM


Have you checked the coolant level? If it's low, it will result in diminished heat, and could be the problem.

Mar 20, 2009 | 2003 Chrysler Town & Country

1 Answer

Blowing cold air when heat is on


air blend door jammed, or you have lost vacumn to the diaphram that opens and closed that door.

Nov 22, 2008 | 2001 Chrysler Town & Country

2 Answers

Cold air when turn on heater


either an air lock in system or thermostat faulty....you could remove faulty thermostat and warm air would get through eventually...or flush thru system and bleed

Nov 15, 2008 | 1996 Chrysler Town & Country

Not finding what you are looking for?
2001 Chrysler Town & Country Logo

290 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...