Question about 2002 Mazda Protege

2 Answers

Where is the blower motor resistor on a 2002 mazda protege?

Heater fan only operates on 4 ( the highest setting) on my 2002 mazda protege ES. I am fairly certain it is the blower motor resistor and I'd like to replace it myself. thanks.

Posted by on

  • Anonymous Feb 03, 2009

    i have the same probleme on my 2003 protege5 at 125 000 kms

  • Anonymous Mar 27, 2014

    How do you check trans fluid on a 2002 Mazda protege hot or cold In park or drve

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Just remove the glove box and its right behind it just take the white pug out and the two phillips screws to remove the resistor out, replace with the new one and cool off!!!! Hope this helps

Posted on Aug 04, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 188 Answers

Behind the control panel in your dash. Where you adjust your heater control.

Posted on Jan 31, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Blower motor not working on 4 1998 Mazda protege


check for power and ground at the blower motor. if this is good then hit motor. if it starts the motor needs replacing. then check the fuse then the fan speed switch for power and ground going to the switch and coming out of switch.

Jul 28, 2015 | 1998 Mazda Protege

1 Answer

Mazda bravo 2.5TD blower fan only works on speeds 3 and 4. Is it the resistor or the fan motor


ballast resistor for sure as this lowers out put to blower motor and increases power as your select a faster setting balast resistor shoud be located on motor or near by hope this helps phil

Aug 16, 2012 | 1998 Mazda B-Series

2 Answers

I have a 2002 protege a/c wont work on all blower speeds and my friends 2000 blower will only work on 2 settings


Replace fan switch in dash.Or may even just need connections cleaned with some wd/40. To replace switch you need to remove dash and knob's, Then you have a switch that has the wires from fan to connector. . If these are ok and clean you need to replace your blower motor, Best of luck to you.
.

Apr 04, 2011 | 2003 Mazda Protege

1 Answer

The heater fan on my 1993 f-350 has become really loud. I only have hi speed which I understand may be a resistor issue but how do I remove the fan and motor assembly to inspect it?


A heater blower motor resistor is an electronic device with three or more progressive resistors that allow the heater blower motor to operate at slower speeds. The highest speed of the heater blower motor is not controlled by the resistor, so when the resistor fails, the fan will often work on the highest speed setting, but not the lower speeds.
To resistor is generally located under the dashboard and under the hood, near the blower motor . The resistor's electrical connector is disconnected, the resistor is removed and the new resistor is installed. On some vehicles it may be easily accessible, and on others it may take partial dashboard removal to replace the resistor.
Look under the hood, generally the wiring for the Blower resistor is attached to the wiring to the blower motor itself
It's inboard & below the motor, near the accumulator. You can see it standing beside the passenger fender. it's the off-white connector behind the L heater hose above the vacuum reservoir & the white WARNING sticker

Feb 12, 2011 | 1993 Ford F350

1 Answer

Heater fan only works on high?


100%: Blower Motor Resistor needs to be replaced. It is located adjecnt to the Blower Motor.

Jan 28, 2010 | 2002 Mazda Protege

1 Answer

2001 Mazda Tribute (3.0 L) Heater motor functions on high only


Its the Blower Resistor....If it was the switch, it probably wouldn't work at all....But the Resistor will give you those symptoms, of working on high med or low

Jan 19, 2010 | 2001 Mazda Tribute

1 Answer

My fan heater only works on the highest setting 6


Hi. This will be the result of a failed resistor switch. the switch controls the current level sent to the blower motor. Once replaced, the motor will operate at your desired rate. This switch is an integrated part of the AC/Heater control cluster, that is mounted in your dash. You will need to remove the trim, and cluster assembly to expose the damaged switch.

Dec 04, 2009 | 2002 Jaguar X-Type

2 Answers

2002 Honda Odyssey fan only works at high speed. The A/C compress


Usually when the blower fan only operates on hi speed, its because of a failed blower motor resistor. You still have hi speed because on hi, the power going to the blower motor goes directly to it, as opposed to the lower speeds, when the power is routed through the resistor, thus lowering the voltage, which in turn lowers the speed of the fan. The resistor is usually located near the blower motor itself, under the hood back near the firewall.

Aug 15, 2009 | 2002 Honda Odyssey

1 Answer

2001 Mazda Protege, Heater and A/C only works on 4 setting


I just had the same problem on my Nissan Xterra and the prblem is the resistor for the AC blower speed.Just get it and you will know.It is right behind and below the glove compartment and it looks like a card once you get it out. It is really easy to replace.

Mar 03, 2009 | 2001 Mazda Protege

Not finding what you are looking for?
2002 Mazda Protege Logo

2,185 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...