Question about 2004 Chevrolet Silverado 2500HD

1 Answer

Blower for heater stopped

The blower motor was working on different settings (high/low) if you played with the switch. When you played with switch trying to get it to come on you could hear clicking under the glove box. The heat was on high and then it stopped working all together. The clicking sounds like a relay type click. It did it several times before but it would always come back on when you played with the settings (1 thru 5) Any ideas?

Posted by on

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 59 Answers

Remove the hush panel under the dash and unplug your blower motor turn the knob and see if its getting power. If it is replace the blower motor. If your heater seems to work on high but not the other 4 settings. replace the blower motor resistor and pigtail (same general location as blower motor)

Posted on Mar 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My heater fan doesn't work at all.


The blower motor resistor is bad ! The blower motor operates at different speeds an when you turn the speed switch It directs current through a different resistor making the blower motor go slower of faster . What Does Blower Motor Resistor Do eHow

Mar 18, 2015 | Cars & Trucks

1 Answer

Heater blower only works on high


Most likely the blower motor resistor or the fise for the low speeds. The high setting for the blower motor is on a separate circuit than the other lower settings.

Dec 04, 2013 | 2008 Chevrolet Hhr

1 Answer

Heater and ac stopped working 1996 gmc sonoma there is a clicking noise when i turn the fan low to high and also the same sound turning switch from off to different blower settings but no air comes out...


probly the switch is burnt-it happens when the blower motor gits old and draws too many amps---so replace blower at same time or else same issue again--and while u gut dashboard all apart inspect ac evaporator and heater core-theyr aging too

Oct 19, 2011 | 1996 GMC Sonoma

2 Answers

Blower motor only works on high


your switch is bad more than likely but different settings send power threw the motor different ways so if one way shorts out another sometimes still works also if you have had a different blower motor put in some only have one speed if you just buy the cheapest one

Dec 15, 2010 | 1999 Chevrolet Malibu

1 Answer

I have high speed blower but no medium or low


It's likely a relay. I've often seen where the lower settings are ran through one relay and the higher setting ran through another because of the difference in amperage. I'd start there, the relays are often pretty cheap and a lot easier to replace than tearing the dash apart to change the switch.

Oct 09, 2009 | 2003 Ford Taurus

1 Answer

I have a 2000 ford E350 van with front and rear air. the front blower motor runs at low speed, The front blower still runs on low even when the knob is set on medium or high. I do not know where the...


it's either the blower motor switch or blower motor resister. Resistor ?Heater Blower Motor Switch Removal Remove the battery (10655) ; refer to Section 414-01 . Remove the battery tray. Remove the screws. Remove the battery tray. Disconnect the heater blower motor switch resistor connector. Remove the heater blower motor switch resistor (18591). Remove the two screws. Remove the heater blower motor switch resistor. ----------------------------------- Switches Removal Disconnect the battery ground cable. Remove the center trim panel; refer to Section 501-12 . Remove the control assembly. Remove the screws. Remove the control assembly. Remove the A/C-heater function selector switch knob. Disconnect the vacuum harness connector. Disconnect the A/C-heater function selector switch connector. Remove the A/C-heater function selector switch. Remove the screw. Remove the A/C-heater function selector switch. Remove the temperature control switch knob. Disconnect the temperature control switch connector. Remove the temperature control switch. Remove the screw. Remove the temperature control switch. Remove the heater blower motor switch knob. Disconnect the heater blower motor switch connector. Remove the heater blower motor switch (18578). Remove the screw. Remove the heater blower motor switch. ----------------------------

Mar 31, 2009 | 2007 Ford E-350 Super Duty Length XLT

2 Answers

Heater blower only blows on low


This could be a few different things:

1.Check the power and ground connections on your blower motor, corrosion can cause high resistance and a slow blower speed.

2. Check your available voltage at the blower motor on the different settings. it should vary with high supplying 12volts, make sure to do this check with the blower motor still plugged in.

3. Connect the blower to a 12v power source and see if it runs at high speed.

If all else fails i would check your resistor pack, i would not suspect this because when it fails you usually just loose all speeds except for high, but it could happen.

Feb 25, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

Replacing heater blower motor


this is not a problem with thw switch or motor. There is a resistor that is mounted inside the dash on the pasenger side that controls the speed of the blwer..these have a tendency to burn up after 10 years or so... replace the resistor, and you will be fine!  http://cgi.ebay.com/ebaymotors/Toyota-Truck-A-C-Heater-Fan-Resistor_W0QQcmdZViewItemQQcategoryZ33548QQihZ016QQitemZ260344846266QQrdZ1QQsspagenameZWDVW#ht_500wt_1230

Dec 23, 2008 | 1984 Toyota Pickup Deluxe

1 Answer

2002 saturn heater


The problem is the blower motor speed control resistor, it is located near the blower motor in the housing.

Nov 23, 2008 | 2002 Saturn Sl

1 Answer

Blower motor starts and stops


It sounds to me like an 'intermittently open circuit', or in plain language, when some part of the heater's circuit heats up a connection somewhere in the circuit 'opens up' stopping the flow of electricity. Then (10 minutes later?) when the circuit cools again the connection 'closes' again until warm. I would trace all the wires in that circuit from the fuse box to the blower motor (including fuse box & fuse) and look for broken or cracked insulation; make sure all connections are tight; I'd certainly check the heater's 'setting' switch (off,high, low switch) on the dash. It could also be a fusible link. This is a piece of wire somewhere in the circuit that 'feels' different than the other wire, more 'rubbery' and not as stiff. It's actually a little thinner wire inside than the rest of the circuit made to burn cleanly through (acting as a type of fuse) rather than over heating the circuit itself The problem has to be in this circuit, and something that 'opens' when heated. Good luck!

Nov 20, 2008 | 1993 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

495 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...