Question about 1989 Toyota Corolla 2 Door

1 Answer

Engine weak willnot hard to keep runing

Act like it jumped timing but i donot think that it has

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Check your plug wires. carefully..when i pulled mine i thought i had the same problem but its just wires...car runs perfectly now.

Posted on May 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car cranks hard start


Out of time, timing belt jumped the cogs, or fuel system faulty.

Check for a clogged fuel filter, or if your fuel pump don't run at all, replace the "fuel pump relay". Sometimes your fuel pump will run, but be too weak to hold pressure, which will let your car idle somewhat, but be too weak to run the engine at speed or under load.

Dec 17, 2013 | Hyundai Cars & Trucks

1 Answer

Chevy truck 2000 4.3 wont start


Have you replaced the cap and rotor ? You could have a weak cap thats allowing the spark to jump to the wrong wires.
You can check compression to see if it really has jumped time.

Jun 24, 2013 | Cars & Trucks

1 Answer

Car won't stay running


You can use code scanner to check the engine system first.

Jun 20, 2013 | 1997 Pontiac Grand Am

1 Answer

Engine runing but wont acelerate when pressing the accelarator pidal


you have a leaking power valve, gasket or accelerator pump , repair or replace .
Test the fuel pump for defective and replace if necessary.
God bless you

Oct 16, 2012 | 2004 Ford Freestyle

2 Answers

My 93 olds cutlass ciera keeps misfiring and stalling, i have change the spark plugs, fuel filter, o2 sensor, maf sensor, and still stalls and misfires any ideas?


For engine misfiring problem check the help links mentioned below. Click the link below to go through the troubleshooting procedure :---- Engine misses and truck jumps? Hard to down shift? Issue with high gear only? http://technoanswers.blogspot.in/2012/02/engine-miss-and-truck-jumps-hard-to.html

-----------
Bad miss at idle?

http://technoanswers.blogspot.com/2012/01/bad-miss-at-idle.html

-----------
While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

------------
Engine Misfire codes for car?

http://schematicsdiagram.blogspot.com/2011/12/engine-misfire-codes-on-chevrolet.html
Engine Misfire codes?

http://schematicsdiagram.blogspot.com/2011/12/engine-misfire-codes-on-chevrolet.html

--------------
Misfire on cylinder 4?

http://schematicsdiagram.blogspot.com/2011/12/misfire-on-cylinder-4.html

-----------
Oil on spark plugs and car misfires?

http://technoanswers.blogspot.in/2012/02/oil-on-spark-plugs-and-car-misfires.html

----------

This will help.

Thanks.

Feb 14, 2012 | 1993 Oldsmobile Cutlass Ciera

1 Answer

1995 jeep wrangler 2.5 i have no power.I ran out of gas in a mud hole the water was up to the doors i put gas in it and got out .I put in a new 02sen,spark plugs & wires buttin cap both trottel body...


I would run a compression check and bleed test to see if you have a weak cylinder due to a cracked head or bad valve...if you sucked some water in the intake or through the exhaust it could of done some internal engine damage.

Aug 06, 2011 | 1995 Jeep Wrangler

1 Answer

My 97 Diamante acts like the battery it totally d...


You have bad terminal..open the battry terminals pour some boiling water over them. then use a sand paper to clean then when ur done doing so install the terminal and put some grease ove them a bit not too much. and tight it well i think it will be ok then.

May 19, 2010 | 1997 Mitsubishi Diamante

1 Answer

I have replaced the timing belt but it keeps slipping. I have all new pulleys and a new tensioner. The belt tends to drift to the inside toward the engine while its running. It runs fine until I start to...


It's not the tensioner pulley. It's the tensioner itself. The spring on the inside has become weak allowing the belt tension to move it just off of "square" to the engine do it's acting like a cone. Smaller on one end than the other. The belt wants to drift towards the smaller end and comes off. Think of it as your arm with a glass of water in your hand extended out in front of you. At first you can hold the glass of water just fine...but after awhile your arm gets tired of holding it there. What happens?

Mar 15, 2010 | Mazda Millenia Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...