Question about 1995 Plymouth Voyager

1 Answer

I need torque specs for 1995 plymouth voyager 2.5l head gasket

Teardown & re-assembly for head gasket

Posted by on

  • Anonymous Mar 15, 2014

    torque spec for intake maniful on 1996 pliymouth grasd voyager



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Plymouth Master
  • 22,306 Answers

Start in middle and work your way outwards,torque setting??you haveing a laugh,no self respecting mechanic uses a torque wrench,pull heads down first with speed key ,making sure the bolt holes in the block are clean and no oil or water in them.then the ratchet then the nice "snap on" bar ,has to be snap on for the right amount of spring.Then use the "snap on" bar to put the final torque on and feel the bolts stretching .If your a weekend mechanic then about 80lbs should suffice but retorque them after a 50 miles or so

Posted on Jan 31, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Need torque specs to replace head gasket on a 1989 plymouth voyager

Normaly supplied with the head gasket with the sequence in which to tighten them.

Jun 24, 2012 | Plymouth Voyager Cars & Trucks

1 Answer

Need to know the torque specs for 1993 voyager van cylinder head. 6 cylinder 3.0 litr

According to what I found online, the torque spec for the 1993 3.0L is 91ft/lbs, loosen and re-torque to 91 ft/lbs

This link is where I got the information, it is a PDF download

Good luck, Jim

May 01, 2011 | 1993 Plymouth Voyager

1 Answer

I wastold Ihave to degree the head bolts on a 94 plymouth voyager 3.0 after torquing. do you know how and how much?

go to any auto parts store and buy a haynes manual for your vehicle. they are based on a complete teardown. for about 20.00. it will tell in this book.if no luck, a dealer for your vehicle can tell you. or give you a read out of the proper torque settings for your engine. see the service dept.

Apr 19, 2011 | Plymouth Grand Voyager Cars & Trucks

1 Answer

Torque specs for 98 Plymouth voyager 3.0 intake manifold

ramundoo_3.giftorque spec is 20 -28 ft is the sequence.thankyou.ramundoo

Mar 16, 2011 | 1998 Plymouth Voyager

1 Answer

1996 plymouth voyager 3.8 oil pan gasket torque specs

The bolts need to be tightened to 105 inch/pounds.

Feb 20, 2011 | Plymouth Voyager Cars & Trucks

1 Answer

I am changing the head gasket on my 92 acclaim 2.5 and was told to change the head bolts as they have been upgraded from 10mm to 11mm but nobody seems to be able to tell me if the torque specs have...

The torque specs should be the same but I have never heard of this before. Make sure you have the head checked for cracks & checked for warpage. It may need to be planed. Be sure to use a top quality head gasket. Good luck!

Feb 02, 2011 | 1992 Plymouth Acclaim

1 Answer

Head bolt Torque specs for a 1998 Plymouth Voyager

according to the manual

Step 1: Bolts 1 - 8 to 61 N·m (45 ft. lbs.)

† Step 2: Bolts 1 - 8 to 88 N·m (65 ft. lbs.)

† Step 3: Bolts 1 - 8 (again) to 88 N·m (65 ft. lbs.)

† Step 4: Bolts 1 - 8 turn an additional 1/4 Turn.

(Do not use a torque wrench for this step.)

NOTE: Bolt torque after 1/4 turn should be over 122
N·m (90 ft. lbs.). If not, replace the bolt.

Nov 25, 2010 | 1998 Plymouth Voyager

1 Answer

91 2.0 subaru legacy, needs head gasket and timing blet replacement. how do i repair?

If you're not a very experienced mechanic, take the car to one. You're going to be pulling off the cylinder head, which requires a LOT of teardown just to get to that point. The way you set up the engine before disassembling even the first bolt is critical, and there are about a hundred little tricks and techniques you're going to need to know before you do such a job.

Here's a photo of my wife's car from this past weekend (copy and paste into your browser) - I replaced the head gasket on her Honda Civic. This was several hours' worth of teardown and cleaning in preparation for installing the new gasket (the new head gasket is in the picture, lying flat with the four large holes for the pistons):

There are specific two-step torque sequences and patterns for reinstalling the head that are crucial to do properly or it'll never seal. I'm sure the information on how to do it, step by step, but if you're going to tackle the job, you'll need a lot of time, an extensive tool set, step by step instructions and torque specs for many of the subassemblies, quite a few new parts (head gasket, head bolts/studs, manifold gaskets, timing belt, timing tensioner, accessory belts, water pump, thermostat, all fluids (since they'll be drained before starting), etc etc etc). It's a huge job and one that is easy to screw up, and on a teardown of this level, one mistake can be all you need to destroy the engine.

Nov 18, 2009 | 1990 Subaru Legacy

1 Answer

What is the torque specs for the transmission oilpan on a 98 plymouth grand voyager/

You don't really need exact specs on that but it is usually around 14 inch pounds... Just use a nut driver or 1/4 in drive ratchet and use a cross pattern on the bolts, not a circle. do not tighten anything 'till you have every bolt in and verify that it goes in easily. Be careful to not crush the gasket, after you get the fluid in, watch for seepage and tighten up wherever you see any . Most important to remove all old gasket material from both pan and trans rail that is the primary cause of leaks.

Jun 19, 2009 | 1998 Plymouth Grand Voyager

Not finding what you are looking for?
1995 Plymouth Voyager Logo

282 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides