Question about 1993 Mercury Grand Marquis

1 Answer

1993 mercury grand marquis the cable on the window assembly has come off due a broken piece of plastic, is there any way to keep the window from being pushed down by hand in this condition

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

You could but a small 2X4 in the shell to keep the window up/Thats about it Please rate my response thank you very much

Posted on Jan 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the top dash cap, not the whole dash, from a 1993 Mercury Grand Marquis


I covered one of mine with a custom dash mat...about $50. from JC Whitney...on line...much cheaper...leather is not usually used on top side of dash due to Sun rays...

Aug 05, 2015 | 1993 Mercury Grand Marquis

1 Answer

Where is fuse box on 1997 mercury marquis


All windows are on the same fuse in your vehicle.
If one window is not working, it is either a switch problem, a motor problem, or a regulator problem.
You will need to remove the door panel and see if the motor is getting voltage when the switch is actuated. If there is voltage at the motor connector when the switch is actuated, check to make sure that the regulator mechanism hasn't seized due to lack of lubrication (they are supposed to be lubricated annually but nobody remembers to do it.... then they seize).
If you can HEAR the motor turning but it is not moving the window, the plastic gear in the motor assembly has broken off. Chances are you will need to replace the window motor.

Jul 29, 2014 | 1997 Mercury Grand Marquis

1 Answer

Back power windowsdont work


The window regulator and/or motor needs to be replaced most likely, old plastic has broken somewhere inside the mechanism that rolls the glass up and down, remove door panel and look inside to see what is actually going on.

Jul 14, 2014 | 1993 Mercury Grand Marquis

1 Answer

Back power windows do not go up or down


The little plastic wheels on your regulator have either broken off or popped out of the track that makes your window go up & down, will need a new regulator because there is no bending it back into posistion, it will bend again causing the same problem.

Jul 14, 2014 | 1993 Mercury Grand Marquis

1 Answer

1996 Mercury Grand Marquis wipers don't work. I changed the motor and the fuse isn't blown


You need to take the plastic cowls off that cover the wiper arm linkage and wiper transmission to inspect it...cowl is held on with 3 Phillips screws near windshield and some one inch wide metal clips, take off the gasket that fits on top. If both are not working check the transmission where linkages attach, if one wiper blade is not working it is usually the drivers side where the nylon bushing that forns a ball/socket sort of connection fails due to build up of debris and the rusting of parts that follows, let me know if this helps.

Dec 17, 2012 | 1993 Mercury Grand Marquis

1 Answer

How to install a new power window motor in my 1993 Mercury Grand Marquis? I have a 1993 Mercury Grand Marquis Ls and the power window doesn't work. So then I bought some new window motors and I was...


Remove all screws to door panel. Remove the lock and window controls. Then take large flat-tip screwdriver and gently pry directly next to plastic studs holding panel on to door. Lift door panel off. Remove plastic out of the way. You will now have access to window motor. You may have to solder off old wiring. Or if you have enough to cut, would be good

Sep 11, 2009 | 1993 Mercury Grand Marquis

1 Answer

How to install the window cable in the rear door


The regulator cables come as an assembly. You need to replace the whole regulator.

Apr 19, 2009 | 2000 Mercury Grand Marquis

1 Answer

Replacing the light switch on a 89 mercury grand marquis


I have had to change this switch. You probably got the dash torn apart down to the piece that the knob on the light switch will keep you from getting that piece off? yes? There is a pin on the light switch frame that has to be depressed. Once you do that, you can pull the knob and shaft out of the switch assembly. After that, the plastic panel will come off and you can R & R the switch. Save that shaft and knob, you will need it for the new switch, unless the new switch uses a different size shaft arragement. Then you may have to but a corresponding shaft/knob assembly. I made the mistake of slicing the knob in half with a Dremel cutter and had to buy a new knob for the shaft.

Uncle Melvie

Jan 01, 2009 | 1988 Mercury Grand Marquis

Not finding what you are looking for?
1993 Mercury Grand Marquis Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...