Question about 1992 Chevrolet Cavalier

1 Answer

Break light bulb replacement - 1992 Chevrolet Cavalier

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 382 Answers

The brake light bulb is accessed from inside the trunk. There are 2 plastic wing nuts that release part of it. Then you pull back the covering just a bit and there are 2 more. That should release the entire Light housing. A small turn and the bulb holder removes from housing. Hope this helps and have a good day.

Posted on Jan 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

S10 pick up back cab break light not functioning


The break light bulb on the back of the cab goes out a lot. Just remove the lens and replace the bulb. Get the bulb from the dealer ONLY! All other bulbs burn too hot and will melt the lens.

Apr 30, 2014 | 2001 Chevrolet S-10

1 Answer

1993 GMC sierra 1500 replaced rear turn signal bulb and break light bulbs..still no break light and turn signal still flashing fast..no hazzard light on same side


the break switch is damaged replace it then the hazzad light and the break light will be ok .. and about the indicator light its circuit's capacitor or the resistor is damaged please check that and replace the same it will be ok

Aug 24, 2012 | Cars & Trucks

1 Answer

Break lights and blinkers not working


If you put the tester on the outlets and it lights up properly but the bulbs dont, you have already concluded that the wiring isn't the problem. unless of course the wires are corroded and simply putting the bulb in shorts it out. Have you tested the bulbs?

Jul 22, 2012 | 2008 Pontiac G6

1 Answer

Bulb failures with no real pattern


check the front and rear turn signal and brake bulbs ,check for filament wear or drakness in bulb glass.if this is found replace bulb,you may also have a bad ground to a bulb socket, turn lights on (signal and break) and wiggle wires at bulb socket, watch light, if it dim any replace that socket and check the ground wire.

Mar 04, 2010 | 1989 Jaguar Vanden Plas

1 Answer

1992 camery


The module reads the bulb amperages, so the bulbs must be the right ones for the car. Pay close attention to the third light and its brightness....921 I believe

Jun 06, 2009 | 1992 Toyota Camry V6

1 Answer

Tail break lights don't work. Window break light does work however. Bulbs have been replaced.


Check the brake light fuse. The high mounted brake light (third brake light) is on a different circuit than the brake lights. Hope this helps.

May 23, 2009 | 1998 Mercury Mystique

1 Answer

2000 Saturn sl2 tail lights


If the 2000 Saturn SL2 is the same as the '99 SL2, then your tail lights bulb is the same bulb as your break light bulb. Now they are dual bulbs, just like your head lights. So just the same way that your brights can work, but your headlight lamp be out, or vice versa, is the same with your break lights. So replace both bulbs and you should be good to go. I just had to replace both mine, one was a tail light out, and the other's break light was out, either way, same bulb. Also, check your manual for the light, or take the light out when you go in to get new ones. I found that for some reason there is some confusion on the bulb in this make in model.

Feb 20, 2009 | 1999 Saturn SL

2 Answers

Any one knows how to connect break lights


have you replaced break light bulbs on both sides of the car   they may be wired threw one another  so if  u loose one  you could loose both  some times  just one or the other bulbs is burnt out

Feb 17, 2009 | 1992 Buick Roadmaster

1 Answer

How replace break light bulb in on a4 2005


Replacement of any bulb in the Tail-light assembly is easier then one thinks.

First thing you need to do is gain access to the trunk area. At the top of
the tail-light area inside the trunk is a small circle that needs to be
opened to expose the bolt that you need to remove.

WARNING: Be careful not to loose this bolt or you are going to have to take
apart your trunk interior to retrieve it.

After the bolt is removed the Tail-light assembly will pull out as follows;
Left side: pull out the right side of the assembly
Right side: pull out the left side of the assembly.
The out side of the assembly is held in place by 2 or 3 small nipples.

There will only be one cable that is connected to the assembly. This does not
have to be removed unless you really want to. On both sides of the assembly
there are 2 clips that hold the light plate to the break light lens. After
the clips are loosened the whole light bulb assembly can be removed and the
bulbs replaced.


Restoring the Break-light assembly.

After you have replaced your bulbs and re attached the the bulb assembly, you
will have to first fit the nipples on the outer side of the assembly then
push the inter side into place. Replace the bolt and tighten. You are done.

Jul 14, 2008 | 2005 Audi A4

Not finding what you are looking for?
1992 Chevrolet Cavalier Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...