Question about 2000 Oldsmobile Alero

1 Answer

Pull the window out of the door

All I want to do is pull the window out of the door for now until I can get it in to a shop in a month and change to have the motor on the power window replaced. I need to get the inside door panel off in order to get in to the window and can't. oh and lost my manual to the car. I know. Great move! Please help

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

Ok to take of the panel if its a front door take backside of mirror cover of then look for pop ups or covers that screews are and under the armrest as soon as you get those out work at bottom of door pull trim out and then up the sides of the trim after that pull up and put disconnect the wiring and that should be it/thanks for using fix ya Please rate my response Thank you very much

Posted on Jan 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does the power window button blink on and off and the automatic feature doesn't work in the 2008 Toyota Sienna?


NOTE:
Anytime the batteryterminal has been disconnected, please initialize the driver's door power windowand front passenger's door power windowafter reconnecting the batteryterminal.

With ignition switchin the "ON" position, do the following:

1. Push down and hold the driver's door power windowswitch to completely open the window.
2. Pull and hold up the driver's door power windowswitch until the window closes.

Continue holding the switch for approximately one second until the switch changes from blinking to a constant illumination.
3. Check for proper operation of the "one-touch open and close" function by fully pushing the switch briefly to the "DOWN" and "UP" positions.

At this time the power window switchfor the passenger's door windowshould be blinking.
4. Push down and hold the passenger's door power windowswitch to completely open the window.
5. Pull and hold up the passenger's door power windowswitch until the window closes.
Continue holding the switch for approximately one second until the switch changes
from blinking to a constant illumination.
6. Check for proper operation of the "one-touch open and close" function by fully pushing the switch briefly to the "DOWN" and "UP" positions.

Feb 09, 2016 | Toyota Cars & Trucks

2 Answers

Power window won't work


if window works sometime, problem is in the motor, brushes probably worn out. so need to replce the motor. I would also change the switch because of 14 years old.

Mar 17, 2013 | 1999 Ford Explorer

1 Answer

How to change left rear window motor on a 1997 f 350


Instructions
    • 1

      Remove the 1997 Ford F350's power window switch from the door panel with the trim tool. Unclip the window switch from the power window wiring harness by hand.

    • 2

      Remove the hex-head screws from the door panel with the socket set. Lift the door panel upward 1 inch before pulling it off the door by hand.



    • 3

      Elevate the window glass to the top of the window channel by hand. Tape the glass to the top of the door with packing tape to prevent it from descending into the door during the repair.

    • 4

      Unclip the F350's power window wiring harness from the power window motor by hand. Unbolt the old power window motor from the door and window regulator with the socket set.

    • 5

      Remove the old window motor before inserting the new power window motor in its place.

    • 6

      Bolt the new window motor to the window regulator and door with the socket set. Plug the power window wiring harness into the new window motor.

    • 7

      Reinstall the door panel by reversing the method employed to remove it.



Nov 05, 2012 | Ford Cars & Trucks

1 Answer

Electric window wont raise. how can i get it to raiser?


you have to pull the door panel off and i would first test the motor make sure it is getting power and that the motor really is fried to do that just take a test light hook it to a good ground and poke wires until you find the power if your not getting power then you need to trace that wire and find out y not, but if you are getting power then try to pull/push up on the window as you use the switch to roll it up to help the motor that might not be strong enough to lift the window, if that dont work then you are going to have to unhook the window motor from the door and the window you may not have to take it completely out just enough so that the teeth on the gears arent touching anymore then push the window up into place and bolt the motor back into place to hold the window were it needs to be, or if you have the money check the wires first make sure there getting power and it is the motor and buy and new motor and install it while you have the door all apart and the motor already halfway out.

Apr 25, 2011 | 1991 GMC Sierra

1 Answer

I want to remove passenger side rear door panel because window is down and won't stay up


Hi,
Hi!!

Here is a little information on how window regulator works. Also step by step instruccions on how to remove and install the window glass.

Door Glass & Regulator Power Windows
Diagnosis & Testing
When the rear window lockout feature is enabled, the circuit is open and no voltage is supplied to the rear window switches. When the feature is not enabled, the circuit is connected to battery positive voltage. If this circuit is shorted to ground when the lockout feature is not enabled, the PWR WDO circuit breaker may cycle continuously OFF/ON until, either the lockout switch is pressed to open the circuit, or the circuit breaker is permanently damaged. All windows may be partially or totally inoperative while the fault is present.
Inspect for aftermarket devices which could affect the operation of the system. Inspect the easily accessible or visible system components for obvious damage or conditions which could cause the symptom. Faulty electrical connections or wiring may be the cause of intermittent conditions.
Removal & Installation
Window Motor & Regulator
  1. Position window approximately half way down in the door.
  2. Remove the interior trim panel.
  3. Remove the water deflector.
  4. Tape the window to door frame to prevent it from moving.
  5. Remove the three front door window regulator motor screws.
  6. Disconnect the electrical connector from the window regulator motor.
  7. Remove front side door window regulator motor.
  8. To install, reverse removal procedure.

Window Switch
Front
  1. Remove the front door pull cup screws and pull cup from the front door trim panel.
  2. Disconnect the electrical connectors from the front door power window control switch.
  3. Remove the front door window control switch using a small, flat-bladed tool at the side of the switch.
  4. To install, reverse removal procedure.

Rear
  1. Remove the rear door pull cup from the rear door trim panel.
  2. Disconnect the electrical connectors from the power window control switch.
  3. Remove the rear door window control switch from the pull cup using a small, flat-bladed tool at the side of the power window control switch to release the power window control switch retainer.
  4. Remove the power window control switch from the rear door pull cup.
  5. To install, reverse removal procedure.

Sep 07, 2010 | 2002 Buick Century

2 Answers

Driver's side window will not roll up. All other windows work fine. Help


replace window regulater and moter...after you chech for power inside door on the plug in at window motor with a circuit tester...

Aug 09, 2009 | 2000 Chevrolet Blazer

1 Answer

97 Accord drivers side window won't go up or down....


Window motors & regulators go bad every day. Pull your door panel, unplug the motor, if you have an ohm meter apply the leads to the leads into the motor. One will be ground the other two will raise and lower (reverse) the motor. If you show resistance between the leads the motor windings are good and the problem may be the window regulator. If you do not have an ohm meter, you can run two wires (one ground, the other hot) and test the motor by applying elec to it.

Jul 02, 2009 | 1997 Honda Accord

1 Answer

Window will not lower when door handle is pulled to open door.


VW window motors are known to be problematic. Lucky you had a service contract, otherwise you may have opted to replace the window motor yourself for substantially less cost.

Jun 15, 2009 | 2003 Volkswagen New Beetle Convertible

2 Answers

Power window on 2001 chevy silvrado


Sounds like your gears are striped out inside the motor. I had the same problem on a car of mine. I just went to a parts store and bought the gear and took the motor apart and fixed it myself. It cost 18 dollars with tax.

Good Luck.

Feb 02, 2009 | 2001 Chevrolet Silverado 1500

1 Answer

1992 f150 power window


If the window motor runs then perhaps the window channels need lube, get a can of silicone spray lube and apply to both window channels until it drips out the door bottom and then retry, if no change replace the regulator.

Jul 25, 2008 | 1992 Ford F150 SuperCab

Not finding what you are looking for?
2000 Oldsmobile Alero Logo

Related Topics:

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...