Question about 2003 Pontiac Aztek

1 Answer

I need to remove & replace the power window module on my 03 Aztek

How do I remove the module?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

Its easy lift from the back of the power switches and pull forward its just clipped in then change out the switch/ Please rate my response thank you very much

Posted on Feb 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are power switch for window control 03 Aztec


I would check the wiring harness going into the driver side door, on the hinge side. The wire harness probably has a protective rubber boot covering, see if you can move cover back so you can see wire colors. The yellow wire is voltage for power window master switch. Black wire is ground. The wire harness is flexed every time the driver door is opened or closed.

I looked at info for Pontiac aztek.

Nov 25, 2015 | Cars & Trucks

1 Answer

Why did security and service engine soon lights come on?


Power windows may not work due to faulty body control ...

repairpal.com > Problems > Pontiac > Aztek
Pontiac Aztek Power windows may not work due to faulty body control module. ...2001 Pontiac Aztek140,000Visitor ... air conditioner pump not engaging no power to relay . fix remove fuse # 28 bcm pump engaged air worked also a short term ...

Aug 30, 2015 | 2001 Pontiac Aztek

1 Answer

Abs module location


Did you clear the codes after you replaced the parts, and were the parts faulty, or does the original problem still exist ?

Feb 20, 2014 | Cars & Trucks

1 Answer

Looking for video on 2001 aztek bcm replacment


What is a BCM? It is a Body Control Module, it is under the Dash, 2 bolts and the Electrical Connector. Remove and Replace.

EASY!!!

Apr 12, 2013 | 2001 Pontiac Aztek

1 Answer

How to replace " cabin


The 2001 model Aztex has 2 cabin filters, they usually come 2 to a box when you buy them.
The charcoal carbon filters are the best.

Removal:

•Open the IP compartment door.
•Remove the rear inside IP compartment door.
•Open the HVAC module assembly access door
•Remove the RH passenger compartment air filter from the HVAC module.
•Slide the LH passenger compartment air filter to the HVAC module opening.
Remove the LH passenger compartment air filter from the HVAC module.

Installation Procedure:

•Install the LH passenger compartment air filter into the HVAC module opening.
Slide the LH passenger compartment air filter toward the left side of the HVAC module.
•Install the RH passenger compartment air filter into the HVAC module opening.
•Close the HVAC module assembly access door.
•Install the rear inside IP compartment door.
•Close the IP compartment door.

I Hope this information is helpful.

Sep 03, 2011 | 2001 Pontiac Aztek

1 Answer

Replacing side view mirror and can't get door skin off


Useing a small screwdriver, gently pry the window switch up, and un plug it.Remove the 3 screws, then with a door panel tool start at the bottom front and pry gently out on the panel, work your way around the door. Lift up on the panel when you have all the clips loose, unplug the mirror connector. In the door right behind the mirror will be a foam pad, remove it then the 3 nuts. The mirror should come right off then. Good Luck

May 14, 2009 | 2003 Pontiac Aztek

2 Answers

2003 where is the modules for the liftgate in a 2003 lincoln Nav


tascafordparts.com for discount.

The liftgate actuator and remote control are in the liftgate.
The module is in the left rear quarter trim panel.


SECTION 501-03: Body Closures 2003 Expedition/Navigator Workshop Manual
REMOVAL AND INSTALLATION Power Liftgate Module Removal and Installation
NOTE: Prior to removal of the power liftgate module, it is necessary to upload module configuration information to a diagnostic tool. This information needs to be downloaded into the new power liftgate module once installed. For additional information, refer to Section 418-01 .
  1. Remove the rear quarter trim panel. For additional information, refer to Section 501-05 .
  1. Remove the power liftgate module.
    1. Disconnect the electrical connectors.
    1. Remove the bolts.
89dd4de.gif
  1. NOTE: Once the new power liftgate module is installed, it is necessary to download the module configuration information from the diagnostic tool into the new power liftgate module. For additional information, refer to Section 418-01 .

-----------------------------------------------------------------------------------------

Principles of Operation
The power liftgate is controlled by the power liftgate module.
The power liftgate module receives inputs from:
  • glass position switch (determines the ajar status of the liftgate glass).
  • forkbolt switch (determines the primary position of the latch).
  • detent switch (determines the secondary position of the latch).
  • home switch (determines the power cinch status).
  • power liftgate control switch (activates the power liftgate from the interior of vehicle).
  • pinch strip switches (determines if an obstacle is detected between the pinch strip and liftgate).
  • instrument cluster module (activates and sets the options for the power liftgate).
  • optical sensor (determines the direction, travel speed and obstacle detection of the liftgate).
  • UBP serial communication link.
The power liftgate module sends outputs to:
  • liftgate motors.
  • power cinching latch system.
  • liftgate chime module.
  • body security module
------------------------------------------------------------------------------------

The liftgate consists of the following components:
  • liftgate window glass latch
  • door lock actuator (power liftgate only)
  • liftgate latch
  • liftgate handle
  • liftgate latch remote control (power liftgate only)
  • liftgate ajar switch
  • chime module (power liftgate only)
  • -------------------------------------------------

Apr 14, 2009 | 2003 Lincoln Navigator

1 Answer

Window switch doesnt work


the panel for these should pop out backward to forward then everything should be exposed. Please rate my response Thank you very much

Jan 31, 2009 | 2003 Pontiac Aztek

2 Answers

Dashboard gages, radio, headlights


BCM needs replaced the cost is around 160.00

Jun 09, 2008 | 2001 Pontiac Aztek

Not finding what you are looking for?
2003 Pontiac Aztek Logo

Related Topics:

243 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...