Question about 2006 Dodge Magnum

1 Answer

Brake lights not lighting up

The top brake light is out on the rear spoiler and preventing the brake lights from functioning properly...i need to know how to get to it to swap the whole LED out.

Please help me before I get a ticket

Posted by on

  • detroit4life Feb 03, 2009

    decklid trim this inside the car? i have taken the interior paneling off and i see 4 holes/openings/cutouts where it looks like the spoiler may be bolted down at...however the bolts look odd as Fu@k is there some kinda special tool involved to remove?



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

First thing take off decklid trim panel there shuold be atleast 4 bolts take the bolts out and pull upwward you will have to get some double sided tape anyway pull of spoiler and should be able to see the brake light twist the bulb out and replace it that is it/ Please rate my response thank you very much

Posted on Jan 31, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My brake lights on the spoiler of my 2004 Lincoln LS do not work.

lift the car and lock inside of the spoiler turn the conector and pull out the light bulb and instal the new bulb light

Jul 22, 2012 | 2004 Lincoln LS

1 Answer

You replace the brake light assembly for a 2005 Subaru Legacy that is in rear wing spoiler

Here's what I did to replace the brake light assembly for the rear passenger side (this would apply to the drive side as well, but not the brake light on the spoiler) on my 2005 Legacy Sedan:

1. Open trunk
2. Pull away the interior liner/paneling around the light. I believe you can remove a few of the black screw/clamps to do this. I just pulled mine out, which works, but is prob not optimal. Take note of how it all sits in as your pulling it out to avoid headaches when putting the paneling back in.
3. Pull off the brake light wiring clamps/screws. Mine had a few white screw/clamps holding part of the wiring to screws on the assembly. These come out easily by applying low pressure and pulling them off.
4. Un-clamp the main (white) brake light clamp. On the top of the clamp, on the side that is the wire coming in (left side for passenger assembly), you apply pressure on the rectangular part of the plastic which releases the clamp, and pull off. I fiddled for this for a bit. You don't need a screw driver or anything, just apply downward pressure on the top of the clamp, on the rectangular portion, on the side that will pull away.
5. Look at your new brake light assembly. You will see 4 screws coming out that have no nuts. These are the nuts (the only ones) you need to remove from the old assembly. I used a socket wrench but pliers would suffice.
6. BE CAREFUL not to drop one of the nuts when getting near the end of the screw. Dropping one and losing it in no-man's land could require a trip back to the store!
7. Once all 4 are removed, gently pull and wiggle from the outside. You can also push and wiggle from the inside. This takes out the assembly.
8. Insert new assembly. The one white screw that extends out from the car will fit into place with the assembly as it gets in.
9. Put the nuts back on and tighten. You will have to do a few rounds of this as the assembly gets tighter in. Don't move on until you have re-checked all nuts and they are snug.
10. Clamp on main light wiring
11. Put paneling back on
12. Check to see if works
13. Gaze at your amazing repair work for a minute and confidently proceed with your day knowing you just saved $100!

Total job takes 15 minutes, tops.


Mar 02, 2012 | 2005 Subaru Legacy

1 Answer

When I hit the brakes, the only brake light that works is the one in the spoiler. the bumper lights and high mount are not lit. the tail lights seem to be working although i have one that needs to be...

Both of your rear lights must be out if it was a brake light switch or fuse you would get no lights at all. It also may be a bad turn signal switch causing the right and left lights to not get power.

Oct 28, 2010 | 2000 Acura TL

2 Answers

Third brake light not working all other tail lights & brake lights work fine

This is a simple bulb replacement.Simply pop off the access cover(if you need to) then twist the bulb in a counter-clockwise motion to remove it.Install is opposite of removal.I hope I could help, rate me accordingly, Thanks.

Oct 11, 2010 | 1993 Honda Accord

1 Answer

When car is turned on all rear barke lights and signals work but when car is off and brake is applied only the spoiler brake light comes on is that supposed to happen like that /

The rear spoiler and both rear lights should come on with the car off and brake applied, but no other lights should,The Only lights that should work on any vehicle when it's turned off is The headlights,brake lights,and hazzard light..

Oct 01, 2010 | Chevrolet Cobalt Cars & Trucks

1 Answer

How do you replace the brake light on the rear spoiler on a 2001 Hyundai Accent?

This is the Spoiler Dude. The spoiler light is attached with screws to the spoiler. You must remove the screws and then the spoiler light will come away from the spoiler. Clip the two wires ( Black & Red ). Attached the new spoiler light ( I can get that for you) with a sleeve. Test the new light with the brake pedal depressed. Screw in the new light and that is it. If you have any questions.
Call Spoiler Dude Paul

Apr 20, 2009 | 2001 Hyundai Accent

3 Answers

Can't get the spoiler, that holds the 3rd brake light on the off

regarding chevy equinox spoiler there are three 10mm bolts one on each end and one in the middle then there are three pins in the middle that snap in. these are very difficult to release without breaking them. If they break use a two part adhesive sparingly to hold the spoiler down or it will hit when you open the hatch.

Apr 05, 2009 | 2005 Chevrolet Equinox

1 Answer

2005 Lincoln Ls 3rd Brake Light Wiring

The best way to wire a third brake light is to run the wire directly from the brake light switch on the side of the steering colum to the light. You will need a test light to find out what wire lights up when you push the brake pedal. Then you can splice into it when you run your wire to the rear light.

Jan 01, 2009 | Lincoln LS Cars & Trucks

1 Answer

How do I change the bulb 2004 infiniti high mount bake light?

Unfortunately, these are not very simple. If you have a factory high mount brake light-meaning not one in a spoiler, you have to remove the rear seats, the rear parcel shelf and then the 3rd brake light. the 3rd brake light I believe is an LED setup which get replaced as an assembly which inserts into the housing. If you need further guidance let me know.



Dec 10, 2008 | 2005 Infiniti G35

1 Answer

2001 pontiac sunfire with no brake lights

If the light in the spoiler works, the switch is good. Sounds like a bad ground to the light sockets

Sep 04, 2008 | 2004 Saturn ION

Not finding what you are looking for?
2006 Dodge Magnum Logo

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides