Question about 2003 Ford E-Series

Open Question

Big end torque settings

2003 ford transit 2.4 td 16 valve

Posted by on

×

6 Suggested Answers

  • 1779 Answers

SOURCE: thermostat replacement 2003 ford focus se, with 2.0, 16 valve ztech engine

Follow the upper radiator hose to where it attaches to a housing (2bolts hold the housing in place) remove the hose clamp here and then remove the housing bolts, inside the housing is your thermostat. Clean off the surface of the housing, and where it attaches to the engine. Install the thermostat, and a new gasket (or O -ring ), carefully replace the housing, being sure the thermostat doesn't slip out of position, tighten the housing bolts, reattach the radiator hose to the housing, add coolant to proper level, check for leaks, u r good to go! Make sure the thermostat is installed in the right direction, if put in backwards the car will overheat. countrycurt0

Posted on Oct 14, 2008

  • 1 Answer

SOURCE: Diagram of Location of a Starter Motor on Ford Transit 2002/2003

replaced starter motor 53 plate t350 90 transit van. lots of dust replaced fly wheel and clutch and sensor :speed up to 50 miles per hour and temp gauge goes up and cuts power

Posted on Dec 08, 2008

  • 2 Answers

SOURCE: what torque for rear wheel bearing Ford Focus 2000

Can only find out that the hub needs to be tightened to
235 nm Dunno if this helps

Posted on Jan 27, 2009

  • 3600 Answers

SOURCE: ford transit 2.4 turbo diese keeps throwing serpentine belt ? any

Most common problem is the tension-er pulley is bad remove the belt and check to see if any pulleys have play in them see if they wiggle back and forth normally the idler pulley bearing wears out and causes the belt to ride at a slight angle marking it throw off the belt. hope this helps.

Posted on Jan 15, 2010

  • 122 Answers

SOURCE: Need to know part number for rear brakes of ford

go to your parts shop with the users manual and the chassis serial number and they can find the original part first and the the immitation if you want!

Posted on May 28, 2010

  • 334 Answers

SOURCE: serpentine belt diagram for 2003

Hello avatar15.jpgeleblanc1234,

Below is a diagram of the belt routing.


8_21_2011_4_43_36_pm.png

I hope this helps.

Regards,

Jerry

Posted on Aug 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque settings on a yaris 1.3 16v big ends,mains,flywheel,cylinderhead


Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

Jul 15, 2016 | 2007 Toyota Yaris

1 Answer

Torque settings for Main,Big end Bearings and Cylinder for Chevorolet Optra 16 valves


people you need to give more info . things change from yr to yr

sorry no clue what yr viehical it is . im guessing if you cant find the torque you wont know to plasi guage the gap between the bearings and crank . better check gap or you could waste all your time putting in new bearings .

Nov 07, 2013 | Cars & Trucks

1 Answer

What are the torque setting for the front discs on a 2003 ford transit


if your doing wheel bearings and youve never done this before,id take it to a mechanic ,there are no torque settings its about experience

Feb 03, 2012 | Ford Transit Connect Cars & Trucks

1 Answer

Hello and help, I need the main bearing, big end and flywheel torque settings for an Isuzu 3.1 td 1997, my manual only seems to have v6 petrol engines in it for some reason. many thanks Ron...


I have a 1997 Rodeo with the V6 3.2L engine. The crankshaft main bearing caps are torqued to 29(lb-ft).

The crankshaft pully is torqued to 123 (lb-ft).

Feb 26, 2011 | Isuzu Trooper Cars & Trucks

1 Answer

Looking for torg specs on tire lug nuts on a 15passenger van f350


Hello there
FORD TRUCK
Wheel Nut Torque Specifications
Make/Model Description Years Torque Make/Model Description Years Torque
FORD (continued)
FORD TRUCK
E250 Van 8 Lug, 9/16" 2008-88 140 -160 ft lbs
E350 Van 8 Lug, 9/16" 2008-88 140 -160 ft lbs
Escape - 2003-01 98
Excursion - 2003-01 160
Excursion - 2000 148
Expedition - 2003-01 150
Expedition 19mm Hex 2000 100
Expedition 21mm Hex 2000 150
Expedition - 1999-97 100
F Super Duty Pickup 10 Lug, 9/16" 2003-99 165
F Super Duty Pickup 10 Lug, 9/16" 1998-96 140
F150 Pickup - 2003-01 150
F150 Pickup 19mm Hex 2000 100
F150 Pickup 21mm Hex 2000 150
F150 Pickup - 1999-88 100
F250, F350 Pickup 8 Lug, 9/16" 2003-01 160
F250, F350 Pickup 8 Lug, 9/16" 2000-99 148
F250, F350 Pickup 8 Lug, 9/16" 1998-88 140
Ranger, Windstar - 2003-87 100

Feb 01, 2011 | 2008 Ford F-350

1 Answer

I need the torque specs for the main and rod bolt for a 99 escort 2.0l engine


engine tightening torques
Main bearings Renew bolts/nuts No
Main bearings Stage 1 43 Nm
Main bearings Stage 2 85 Nm
Big end bearings Renew bolts/nuts Yes
Big end bearings Stage 1 15 Nm
Big end bearings Stage 2 90°

Jan 21, 2010 | 2004 Ford Focus

1 Answer

Torque settings clio 1.5 dci big end shells


whats the torque setting for big end bearing bolt and cylinder head bolt for toyota corolla 12 valve 2E,1990.

Jan 12, 2010 | 2000 Renault 181

1 Answer

Differential Torque settings for 2003 Town Car


New cylinder head bolts are required and an angle guage,or you can make one up with card and a set square. Head bolt torque is 25Nm(newton metres)+60degrees + 60deg + 60 deg so it's a four step process.Con.rod bolts(big-end)28Nm,Inlet manifold 28Nm,Exhaust manifold 25Nm, Crank pulley 40Nm,Sump 5Nm and use locking compound (loctite)Timing cover 6Nm. Valve clearance,set inlets to .006" and ehausts to .010"(set approx.when cold then re-adjust while warmed engine is idling.

Feb 20, 2009 | 2003 Lincoln Town Car

Not finding what you are looking for?
2003 Ford E-Series Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...