Question about 1999 Jeep Grand Cherokee

1 Answer

Cant find location of Block hearter cord on 99 Chrysler

Looking for the location of block heater cord on 99 Chrysler Town and Country LXI Minivan........I have looked everywhere......but cant seem to find out ........any help please

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

Usually it is routed out near the headlight.... there is a good chance tho that vehicle doesn't have a block heater. look at the sides of the motor for round metal shaped plugs in the block (frost plugs) do you see any with an electrical fitting ?

Robert

Please take a moment to rate this solution thanks

Posted on Jan 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Crankshaft position sensor for 2005 chrysler town and country


when looking at the left hand side of the engine ( from the front or belt side ) it would usually be down on the block to the side of the crankshaft damper pulley and 4-5 inches back from the front of the engine.

Mar 08, 2012 | 2005 Chrysler Town & Country

1 Answer

Where exactly is the crankshaft position sensor located in a 1996 town and country lxi (3.8L engine)?


Hello sam adamzz: My name is Roger and I will help you. You can locate the crankshaft position sensor in the transmission bell housing. Standing at the driver side fender. Look at the back af the engine where the transmission and block meet. Just to the right of the block edge mounted in the bell housing you should see a round sensor with a wire lead out of it. This should be the sensor you want. Should you need further help please just ask. Please rate the answer. Thank You for using Fix Ya. Roger

Jan 15, 2011 | 1996 Chrysler Town & Country

1 Answer

2001 Chrysler Town & Country air conditioner/heater blows on high only. We have replaced the front blower relay and it still doesn't work. The back blower is the same.


THE REASON THE BLOWER ONLY WORKA ON HIGH IS BECAUSE OF SOMETHING CALLED THE BLOWER MOTOR RESISTOR. THIS IS A BLOCK WITH ABOUT THREE DIFFERENT RESISTORS ON IT WHICH CONTROL THE AMOUNT OF VOLTAGE THAT REACHES THE BLOWER MOTOR THUS GIVING YOU YOUR DIFFERENT SPEEDS.
THIS BLOCK IS USUALLY LOACATED BEHIND THE GLOVE BOX AND IS BOLTED TO THE HEATER HOUSING.

Jun 09, 2010 | 2001 Chrysler Town & Country

1 Answer

Whats involved in installing a factory block heater on a 2003 chrysler town and country mini van with a 3.3 v6?


it is easy, but u must remove a core plug from the side of the block, then the heater goes there, u will need a car lift to do this.

Jan 08, 2010 | 2003 Chrysler Town & Country

1 Answer

Where is the block heater cord on a 2008 Chrysler Town & Country Limited?


it should be in front near the grill, was there a block heater installed on this van? if you look at the engine were the freeze plugs go ,if a heater was installed you should see the element in one of the freeze plug holes instead of a freeze plug, if there is one then follow the cord, hope this is helpful, good luck.

Dec 12, 2009 | 2008 Chrysler Town & Country

1 Answer

Where is the body control module located on a 1997 town & country


It is located on the back side of the underdash fuse box (junction block). You remove the lower steering column cover and knee blocker reinforcement. Then remove two plugs from the bottom of the BCM.
Remove the bolts holding the junction block to dash panel mounting bracket. Remove the junction block from the bracket. Remove screws holding the BCM to the junction block. Slide the BCM downward to disengage guide studs on jb from channels on BCM mounting bracket

Mar 23, 2009 | 1999 Chrysler Town & Country

1 Answer

Tryin to find out where a block heater is on a 99Chrysler town and country minivan


If this vehicle came with a block heater, it would be either on the side of the engine block lower down(you should see an three core electrical cord coming out of the connection.)Or it could be located on the lower radiator coolant hose.
But be aware,that not all vehicles came with block heaters. you may have to have one installed.

Jan 30, 2009 | Chrysler Town and Country Cars & Trucks

1 Answer

Where is the Body Control Module located?


It is located on the back side of the underdash fuse box (junction block). You remove the lower steering column cover and knee blocker reinforcement. Then remove two plugs from the bottom of the bcm.
Remove the bolts holding the junction block to dash panel mounting bracket. Remove the junction block from the bracket. Remove screws holding the bcm to the jb. Slide the bcm downward to disengage guide studs on jb from channels on bcm mounting bracket
Remove bcm from jb.

Jan 02, 2009 | 1999 Chrysler Town & Country

1 Answer

99 Grand Voyager


My 98 Grand Voyager 3.3L engine # is located on the rear of the cylinder block, below the cylinder head, your 99 should be the same location. It contains the last digit of the model year, manufacturing plant, engine, usage (car, truck), month/day, serial code (last 8 digits of vin). countrycurt0

Oct 15, 2008 | 1998 Chrysler Town & Country

Not finding what you are looking for?
1999 Jeep Grand Cherokee Logo

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...