Question about 2005 Honda Civic

1 Answer

During start Automatic gear does not change

During the Start Automatic gear does not change from Park position to any other position. I can operate the gear by relising the mechanical lock and moving the gear to position N (by inserting the key in to the hole infront of the gear handle). The car drives fine with no other problems. When I stop the car I can move the gear to the park position. Once I move the gear to Park position I can not move the gear, it locks.

Look forward to hear from you

Best regards
Halil

Posted by on

  • hyorganci Feb 03, 2009

    The brake switch was found to be faulty. Thanks for your help. the solution was spot on.

  • Anonymous Mar 25, 2014

    I started my car an it got stuck in starting making starter stoll position an made noises when gears chang

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 21 Answers

Sounds like a brake switch failure. located under the brake pedal and is fairly simple to change out.

Posted on Feb 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Holden cruze 2009 key stuck in the ignition won't go to off position , can't get it out of park .What is the problem ?


Is it shifter on the floor ?
Ignition Lock Cylinder Control Actuator
If the vehicle is equipped with a floor mounted console gear shifter, it has a ignition lock cylinder control actuator system in the steering column. The ignition lock cylinder control actuator's purpose is to prevent the ignition key from being turned to the OFF position when the transmission is in gear and the vehicle may still be moving. The column ignition lock system consists of a ignition lock cylinder control actuator , and a park position switch that is located in the A/T shift lock control switch. The ignition lock cylinder control actuator contains a pin that is spring loaded out to mechanically prevent the ignition key cylinder from being turned to the lock position when vehicle transmission is not in the Park position. If vehicle power is lost, and/or the transmission is not in the Park position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column.

GM had problems with these ! Has a TSB - technical service bulletin !
Automatic Transmission Shift Lock Control Description and Operation
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
• The automatic transmission shift lock solenoid (serviced as the automatic transmission shift lock actuator), as well as the body control module (BCM) and the engine control module (ECM). The shift lock solenoid is located within the floor shift control assembly with vehicles equipped with floor shift.
• The BCM controls the voltage to the shift lock control solenoid through the shift lock control solenoid controlled voltage circuit. The following conditions must be met before the BCM will remove voltage from the shift lock solenoid:
- The ignition is in the ON position.
- The engine control module (ECM) sends an input via GMLAN serial data to the BCM indicating the transmission is in the PARK position.
- The BCM determines the brake pedal is applied according the brake pedal position.
Since the shift lock control solenoid is permanently grounded, the BCM supplies voltage to the automatic transmission shift lock control solenoid, mechanically locking the shift lever in the PARK position as the solenoid energizes. When the brake pedal is applied, the BCM turns the control voltage output of the shift lock control solenoid OFF, de-energizing the shift lock control solenoid. The de-energized solenoid releases the mechanical lock allowing the driver to move the shift lever out of the PARK position. When the transmission is out of the PARK position, the shift lock control solenoid remains de-energized.
During remote start operation, the BCM will energize the shift lock control circuit, locking the shift lever in the PARK position.
Replaced shifter on a cobalt , broken plastic part inside , wouldn't press on micro switch to disengage ! Found replacement shifter at auto slavage yard .$20.00 US

Sep 03, 2016 | Holden Cars & Trucks

1 Answer

My torrent will not start and the key will not come out what do I do


What year is it ? Does yours have floor mounted gear shifter on the console ?
Ignition Lock Cylinder Control Actuator
If the vehicle is equipped with a floor mounted console gear shifter, it has a ignition lock cylinder control actuator system in the steering column. The ignition lock cylinder control actuator's purpose is to prevent the ignition key from being turned to the OFF position when the transmission is in gear and the vehicle may still be moving. The column ignition lock system consists of a ignition lock cylinder control actuator , and a Park position switch that is located in the automatic transmission (A/T) shift lock control switch. The ignition lock cylinder control actuator contains a pin that is spring loaded out to mechanically prevent the ignition key cylinder from being turned to the Lock position when vehicle transmission is not in the Park position. If vehicle power is lost, and/or the transmission is not in the Park position the operator will not be able to turn the ignition key to the Lock position and will not be able to remove the ignition key from the column.

Jun 21, 2016 | Pontiac Torrent Cars & Trucks

1 Answer

Where is location the automatic transmission shift lock relay in my s10 1998 2.2 2wd


Automatic Transmission Shift Lock Control Description
The brake transmission shift interlock (BTSI) system prevents the automatic transmission from being shifted out of PARK unless the brake pedal is depressed. When the brake pedal is depressed, the BTSI solenoid releases a lock pawl. This enables the shift linkage to move and the shift lever to operate.
When service operations are required, the BTSI system can be overridden.
On vehicles equipped with a column-mounted shift lever, override the BTSI system by performing the following steps:
  1. Turn the ignition switch to the OFF position.
  2. Remove battery voltage from the solenoid.
  3. Turn the ignition switch to the ON position.
For vehicles equipped with floor-mounted shift levers, an override lever is mounted on the right side of the assembly. The override lever can be accessed by removing the shift lever boot. Push the lever to the left in order to override the BTSI.
Which does your S-10 have column or floor shift ? No relay ,has a solenoid .
With Column Shift A/T
The brake transmission shift interlock (BTSI) system prevents the automatic transmission from being shifted out of the PARK position unless the following conditions are present:
?€¢
The brake pedal is depressed.


?€¢
The ignition switch is turned to the RUN or the START position.

When the ignition switch is in the RUN or the START position, the current flows from the B/U Lamp fuse located in the underhood bussed electrical center (UBEC) through CKT 839 (PNK) to the park/neutral position switch. The park/neutral position switch also feeds the backup lamps portion of the switch. With the transmission in the PARK position, the current flows to the BTSI fuse located in the underhood bussed electrical center (UBEC) through CKT 275 (LT GRN). The current then flows to the TCC/stoplamp switch through CKT 584 (LT GRN/BLK). The current continues to the BTSI solenoid through CKT 1135 (DK GRN/WHT). The ground path is provided through CKT 1850 (BLK) to G207. When the brake pedal is depressed, the normally closed contacts in the TCC/stoplamp switch open and the current flow is interrupted. When the current flow is interrupted, the BTSI solenoid de-energizes. The transmission may then shift to another gear. When the transmission shifts to another gear (except PARK), the contacts in the park/neutral position switch open. This condition stops the current flow to energize the solenoid when the brake pedal releases.

Whic

Jun 09, 2016 | 1998 Chevrolet S-10 Pickup

2 Answers

This morning it started fine but will not come out of gear and my airbag light is on. Someone said it was the fuse but I am not sure which fuse. Any ideas ?


I am mechanic I really need to no more make ect. but it could be battery or the ignition switch or ignition lock n key but like I said need more information this is a guess that I told you

Oct 21, 2015 | 2008 Chevrolet Chevrolet TrailBlazer LT

1 Answer

Automatic not changing gears


check the shifter mechanism for binding up and not moving freely into positions. Not starting in park but in neutral indicates something is out of alignment with the shifter. May just need cleaning and a bit of oil/grease to fix.

Feb 08, 2014 | Mitsubishi Pajero Cars & Trucks

1 Answer

2004 suzuki automatic transmission stuck in park


that is park lock failure, build into the shifter section,it has an
electric solenoid lock. and a bypass button.
in the glove box, see oper. guide, it tells you where the erg. release
button location, and varies by sub body type and options.
its hidden cover, or a slot, on most cars. the slot type is to insert
any key in slot and push. bang, it opens (brake set,etc)

Dec 25, 2013 | 2004 Suzuki Verona

1 Answer

My 2001 Jeep Grand Cherokee wont start sometimes, but if I put it in neutral then try to start it..It starts .. What is the problem with my baby.......


Test/Service/Replace

The circuit on newer cars with automatic transmissions has a neutral safety, or neutral start switch installed between the ignition switch and the starter. The ignition switch cannot operate the starter motor unless the transmission is in park or neutral.
Late model vehicles with manual transmissions have a starter/clutch interlock switch that requires the clutch to be depressed to the floor.
Neutral Safety Switch
Normal operations of a neutral safety switch provides a quick check for the adjustment of the gear selector linkage.
  • To do this, move the selector slowly until it clicks into the PARK position.
  • Turn the ignition key to the START position.
  • If the starter operates, the PARK position is correct.
  • After checking the PARK position, move the lever slowly toward the NEUTRAL position until the lever drops at the end of the NEUTRAL stop in the selector gate.
  • If the starter also operates at this point, the gearshift linkage is properly adjusted.
  • This quick test also tests the adjustment of the neutral safety switch.
  • If the engine does not start in either or both of these positions, the neutral safety switch or the gear selector linkage needs adjustment or repair.

CAUTION
Since you must work under the vehicle to adjust most shift linkages make sure you properly raise and support the vehicle before working under it. Also, wear safety glasses or goggles while working under the vehicle.
A voltmeter can be used to check the switch for voltage when the ignition key is turned to the START position with the shift lever in PARK or NEUTRAL. If there is no voltage, the switch should be adjusted or replaced.

Jan 26, 2013 | 2002 Jeep Grand Cherokee

1 Answer

Vw jetta automatic not reading park or 1st gears on dash


is a mechanical linkage or electic indacator if it linkage just adjust it ot take it to transmision shop they can adjust it for you

Nov 28, 2012 | 1996 Volkswagen Jetta

1 Answer

DISCONNECT BRAKE PEDAL 1991 SUBURBAN


98 Suburban 5.7L, automatic trans is stuck in park - no previous shifting problems, I know that the brake switch also operates the brake/transmission solenoid (BTS). Stepping on the brake pedal prior to starting the vehicle allows shifting from park to another gear. When I switch the key to the "on" position, I don't hear the BTS click. I can start the vehicle and the brake lights work fine. I just can't shift out of Park. I am unemployed and I am trying to troubleshoot this problem and fix it myself. Please help!

May 24, 2012 | 1983 Chevrolet Silverado

1 Answer

P1646 how much to repair


P1512 Throttle Position Sensor Idle Switch Sense Circuit

P1513 Throttle Position Sensor Idle Switch Sense Circuit

P1514 Park/Neutral Position Switch High Load Neutral/Drive

P1516 Gear Change Park/Neutral Malfunction

P1517 Engine Cranking Park/Neutral Malfunction

P1607 MIL Output Circuit

P1608 Automatic Transmission

P1609 Internal ECM Error

P1641 Fuel Pump Relay No. 1

P1646 Fuel Pump Relay No. 2

P1739 Automatic Transmission

P1775 Transmission Control Module MIL Circuit

P1776 Torque Reduction Request Signal

P1777 Torque Reduction Circuit

P1780 Automatic Transmission

P1781 Automatic Transmission

P1782 Automatic Transmission

P1783 Automatic Transmission

P1785 Automatic Transmission

P1790 Automatic Transmission

P1791 Automatic Transmission

P1792 Automatic Transmission

P1794 Automatic Transmission
P1796 Automatic Transmission
as you can no such code exists for a jaguar ,contact code reader manufacturer

Jan 03, 2011 | 2004 Jaguar S Type

Not finding what you are looking for?
2005 Honda Civic Logo

Related Topics:

330 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...