Question about 1999 Honda Passport

1 Answer

My 1999 Honda Passport has a wiper problem. Time delay does not work. Also when you switch wipers off blades do not go back to bottom position.

Posted by on

  • careylee Feb 21, 2009

    My 02 has had the same problem for years, now the rear wiper has quit also. Changed out the (rear) motor, but that just wasted $90. What now coach?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 50 Answers

I bet your rear wiper is inop also there is a little box in the passenger kick panel area it called the timing and relay control module this has been a common problem in the passports and rodeos

Posted on Jan 31, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can the wiper linkage cause the wipers to park vertical. Wipers work fine on all settings. Tried repositioning the wiper arms but it didn't work


normally if the wiper arms park in the wrong place , it is the fitting of the wiper arms on the pivot that is wrong
try pulling the wipers back off the windscreen , run them through a cycle and then switch off normally
that will be the park position in the motor gear box
then remove each arm from the pivot and re- position it about 1" from the bottom of the screen
that will be the parked position for the wiper blades
having done that then again pull the arms back of the screen and cycle as if wiping the screen
switch of and see where the arms now park on the screen
if it is close to where you set them then that is the park position
next run the wipers a cycle and see if at full movement one arm puts the blade over the edge of the screen or hits the edge
switch off and re-position that arm closer to the bottom of the windscreen
it is time consuming but the only way to park wipers properly as there is no master spline to set in the correct position
If they park any where after this exercise ,replace the wiper unit as there is a problem in the contacts in the motor box.

Sep 14, 2015 | Cars & Trucks

1 Answer

Winshield wiper delay intermitent module making noises


The wiper delay is in the steering column. It's a small box about 2 x 2 inches with a wiring harness attached. With the testing procedures I found below, you should be able to figure it out. I found wiper delays on eBay for around $10 to $20. Good luck.

WINDSHIELD WIPERS CHEROKEE, COMANCHE & WAGONEER 1. POWER INPUT Remove circuit breaker. Test battery side of circuit breaker. If battery voltage is not present, repair open to splice. Test across circuit breaker terminals. Tester reading should be zero (0) ohms. If not, replace circuit breaker. 2. GROUND Connector A unplugged. Test terminal G. Tester reading should be zero (0) ohms. If not, repair open to ground. 3. INTERMITTENT WIPERS Ignition switch in ACCY. Remove delay module and plug connectors together from the module. If wiper operate in LO and HI speed modes and mist (washer) is working, if wipers and mist operate, replace intermittent module. If not go to step 4. 4. WIPER/WASHER SWITCH Ignition in RUN, wiper switch position as indicated, back probe switch side of connector A for standard, connector B for intermittent: Test connector terminal E-wiper switch in LO and mist/intermittent. If battery voltage is not present, replace switch. test connector terminal C-wiper switch in HI. If battery voltage is not present, replace switch. Test connector terminal F-wiper switch to OFF. If battery voltage is present until wipers stop and then voltage drops to zero (0), system is working fine. If this does not occur, replace switch. 5. INTERMITTENT WIPERS Connector B unplug. Test across terminal A and D while rotating switch from minimum to maximum delay. If tester reading is not between 0-500 ohms, replace switch. Test across terminal A and G while rotating switch from minimum delay to maximum delay. If tester reading is between 0 and 500 ohms, replace wiper module. If not replace switch. 6. WIPER MOTOR Ignition in ACCY, wiper switch position as indicated, probe connector D. Test connector terminal 1. If resistance is no zero (0) ohms,repair open to ground. Test connector terminal 4-wiper switch in any position. If battery voltage is present, replace motor. if is not repair open from fuse panel. Test connector terminal 2-wiper switch in LO. If battery voltage is present, replace motor. If not , repair open from wiper switch. Test connector terminal 2-wiper switch in HI. If battery voltage is present, replace motor. If not , repair open from wiper switch. Test connector terminal 5-wiper switch OFF with voltmeter connected. If battery voltage is present until wipers stop and then voltage drops to zero, system is OK, replace motor. If not, repair open from wiper switch.

62217_jeep1_1.jpg


62217_jeep2_1.jpg

Found on the web. I hope this helps.
Rich Long

Jan 26, 2014 | Jeep Cars & Trucks

1 Answer

Windshield Wipers don't return when shut off. No intermittent function. Rear windshield wiper does not work at all.


the internal switch inside the wiper motor gear box is bad.
ive fix many a switch (filed the contacts, and good for 50k more)

Oct 01, 2013 | 1999 Honda Passport

2 Answers

Does any one know if a 1999 dodge ram 2500 has a wiper delay module on it. my wipers will not park.


if you changed your wiper motor and did not turn it on and let the motor return to park before installing blades,i would remove the blades ,turn on the wipers and then off and wait till they do park,then reinstall blades.

Nov 21, 2011 | 1999 Dodge Ram 2500 4WD

1 Answer

How do I operate the rear wiper blade? Honda Passport 1996 4WD.


It should be on the same stalk as your front wipers, you may have to push the stock forward or back to engage the rear wiper

Aug 20, 2009 | 1996 Honda Passport

2 Answers

2002 Honda Passport back wiper and back washer not working


the sprayer for the rear wiper is labeled on the stick with the switch. check the wiring in the tailgate.and the fuse for the wiper.

May 14, 2009 | 2002 Honda Passport

1 Answer

99' Honda Passport driver side wiper stopped working


the main motor is on the passenger side. there is a link between the to that operates the driver side wiper. the link has to be replaced.. what i am finding is that you have to buy the whole wiper kit which is approx.70 dollars instead of just buying the link or gromet.

Feb 23, 2009 | 1999 Honda Passport

1 Answer

Wiper blades will not home.


The home position is a function of the wiper motor. You need a new one.

Feb 09, 2009 | 2001 Hyundai Sonata

1 Answer

Delay wipers don't work.


Try making sure the connection is good.
If it is then you should try replacing the wiper switch.


Brandon Bird

Jan 25, 2009 | 1999 Jeep Cherokee

Not finding what you are looking for?
1999 Honda Passport Logo

Related Topics:

413 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

63577 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...