How to Remove 1993 Toyota Tercel Windshield Washer Pump

Removal Procedure
1.) Remove the washer solvent from the washer solvent container.
2.) Remove the air cleaner intake duct.
3.) Disconnect the washer pump electrical connector .
4.) Disconnect the washer hose from the washer pump.
5.) Disconnect the washer solvent level sensor electrical connector.
6.) Remove the washer solvent container screws.
7.) Remove the washer solvent container from the frame rail.



Installation Procedure: the reverse process of removal

Remove the bolt holding the reservoir to the fender. Lift the reservoir up and disconnect the washer hose and electrical connector. Remove the entire reservoir from the vehicle and drain. Replace pump

A washer pump in a car's windshield wiping system moves washer fluid from a reservoir through hoses. The motorized pump pressurizes the fluid to allow it to be squirted from the hoses through nozzles onto the front and/or rear windshield of a car. The washer fluid helps windshield wipers get rid of rain, dirt, or other objects that can interfere with a driver's visibility. If your washer fluid is not being sent out when activated, the solution could simply be filling the washer system's reservoir with more fluid or cleaning the nozzles and hoses. In more severe cases, the washer pump may need to be replaced. Here are steps to troubleshoot a windshield-washer pump.

Try this link in case you are stuck:

How to Troubleshoot Windshield Washer Pump

Here is another YT video for a similar purpose:

Windshield Washer Pump and System Diagnosis

The hose could be clogged ! Do you know where you add the washer fluid ? Somewhere on the bottom of that plastic bottle is the washer pump .
Removal and Installation
> WARNING: Windshield washer solution contains methanol, which is poisonous. Observe all cautions and warnings indicated on label of washer solution container. Failure to follow these instructions may result in personal injury.
> CAUTION: When replacing the windshield washer pump be careful not to damage the rubber grommet.
> CAUTION: Do not operate the windshield washer pump before filling the reservoir. Failure to do so could result in premature pump failure.

1. NOTE: When installing the reservoir, the filler neck must be lubricated using a water-based lubricant.
   Remove the bolt and the windshield washer reservoir filler neck.

1. Remove the RH fender splash shield. For additional information, refer to Section 501-02 .

1. Remove the foam filler and remove the retainer.

1. Remove the 2 screws and the accessory drive splash shield.
   • To install, tighten to 5 Nm (44 lb-in).

1. Remove the nut, 2 bolts and position the A/C accumulator aside.
   • To install, tighten to 9 Nm (80 lb-in).

1. Unclip the A/C lines from the inner fender well.

1. Drill out the rivet and remove the bracket.

1. Remove the 2 bolts, slide the windshield washer reservoir assembly forward to release it, and position the washer reservoir aside.
   • Install the upper bolt followed by the lower bolt, and tighten to 5 Nm (44 lb-in).

1. Disconnect the windshield washer tube assembly from the pump and release the windshield washer tube assembly from the washer reservoir.

1. Disconnect the electrical connector from the windshield washer pump.

1. Release the wiring harness from the reservoir, and remove the washer reservoir.

1. To install, reverse the removal procedure.

it locate in tthe bottom of windshield water reservoir(tank)

Windshield Washer Pump Removal & Installation To Remove:

1. Remove the air cleaner assembly.
2. Remove the bolts.
   
   
3. Position the pump and reservoir aside.
4. Disconnect the electrical connectors.
5. Disconnect the washer hose.
6. Remove the pump and reservoir.
7. Remove the washer pump.

WARNING
Windshield washer solution contains methanol which is poisonous. Observe all cautions and warnings indicated on label of washer solution container.
NOTE: Windshield washer fluid should be collected in a container after the windshield washer hose is disconnected.
To Install:
WARNING
Windshield washer solution contains methanol which is poisonous. Observe all cautions and warnings indicated on label of washer solution container.

1. Install washer pump in reservoir.
2. Install washer pump reservoir assembly.
3. Connect washer hose.
4. Connect washer electrical connector.
5. Install air cleaner assembly.

---
The windshield wiper fluid pump is located in the tank which is not in the heater motor or defroster area in the dash.

The defroster/heat control door is located in the dash board area:

Air Door Actuators, Cables or Motors Removal & Installation Air Inlet Door Vacuum Control Motor To Remove:

1. Remove the instrument panel lower insulator cover.
2. Disconnect the vacuum connector.
3. Remove the control arm clip and the spring.
4. Remove the nuts and the air inlet door vacuum control motor.

Air inlet door vacuum motor mounting screws

To Install:

1. Install the vacuum motor on the mounting bracket.
2. Connect the control arm and spring.
3. Connect the vacuum hose to the vacuum motor.
4. Install the lower instrument panel lower cover.

Floor Defrost Door Vacuum Control Motor To Remove:

1. Disconnect the negative battery cable.
2. Remove the left lower dash insulator panel and disconnect the lamp.
3. Remove the two pin-type retainers and remove the fill panel.
4. Remove the DLC mounting screws.
5. Detach the vacuum line.
6. Remove the lighting module.
7. Remove the screws and the bracket.
8. Remove the floor/defrost door vacuum control motor.

Floor/Defrost vacuum motor mounting screws

To Install:

1. Connect the vacuum lines and install the floor/defrost vacuum motor.
2. Install the bracket and lighting control module.
3. Install the DLC bracket and mounting screws.
4. Install the fill panel.
5. Install the left lower dash insulator panel.
6. Connect the negative battery cable.

Panel Door Vacuum Control Motor To Remove:

1. Remove the instrument panel.
2. Reach through the door opening and remove the pin.
3. Disconnect the panel door vacuum control motor vacuum line.
4. Remove the screws and remove the panel door vacuum control motor.

To Install:

1. Install the panel door vacuum motor.
2. Connect the vacuum line to the panel door motor.
3. Reach through the opening and install the pin to the linkage.
4. Install the instrument panel.

Windshield Washer Motor REMOVAL & INSTALLATION 1987-95 Vehicles

1. Disconnect the negative battery cable.
2. Drain or siphon the washer solvent from the reservoir.
3. For 1987-91 vehicles, remove the brace.
4. Unfasten the reservoir screws.
5. Detach the electrical connectors and washer hose.
6. If necessary, remove the reservoir from the vehicle.
7. Remove the washer pump motor from the reservoir. Fig. 1: Location of the windshield washer fluid reservoir and pump - 1987-91 vehicles
   To install:
   
8. Install the washer pump motor on the reservoir. Make sure the pump is fully seated in the reservoir gasket.
9. Position the reservoir in the vehicle.
10. Attach the electrical connectors and washer hose.
11. Install the reservoir retaining screws.
12. Install the brace.
13. Fill the reservoir with washer solvent.
14. Connect the negative battery cable, then check for proper washer pump operation.

1996-99 Vehicles

1. Disconnect the negative battery cable.
2. Drain or siphon the washer solvent from the reservoir.
3. Detach the electrical connectors from the washer.
4. Disconnect the hose from the washer pump.
5. Loosen the nut at the bottom of the washer reservoir.
6. Unfasten the 2 nuts, then remove the washer solvent reservoir.
7. Remove the washer pump from the container.
8. If necessary, remove the solvent lever sensor switch from the washer solvent container. Fig. 2: Exploded view of the washer fluid reservoir, pump and level sensor
   To install:
   
9. Install the solvent level sensor switch in the washer solvent container. The tab on the solvent level sender switch must be lined up with the slot in the hole.
10. Install the washer pump into the reservoir, making sure the pump is pushed all the way into the container seal.
11. Install the washer solvent reservoir and secure with the 3 nuts. Tighten the nuts to 44 inch lbs. (5 Nm).
12. Attach the electrical connectors to the solvent level sensor and washer pump.
13. Connect the hose to the washer pump.
14. Fill the reservoir with washer solvent.
15. Connect the negative battery cable, then check for proper washer pump operation.

One can get a repair kit that includes a new motor pump and wiring clips, or

one can get the original motor that plugs into the windshield wiper fluid reservoir.

---
Windshield wiper reservoir (gives idea of how to change the windshield wiper fluid pump motor) Removal & Installation To Remove:

1. Disconnect and isolate the negative battery cable.
2. Raise and safely support the vehicle.
3. Remove the right front wheel and splash shield.
4. Disconnect the electrical connectors from the pumps and detach the rear washer hose.
5. Place a drain pan under the reservoir if it contains fluid.
6. Disconnect the front washer hose at the wiper unit in the engine compartment. NOTE: The front hose will be removed with the reservoir.
   
7. Let the fluid drain from the reservoir.
8. Remove the mounting screws and the reservoir.

To Install:

1. Install the fluid reservoir with the mounting screws.
2. Connect the front washer hose in the engine compartment.
3. Connect the electrical connectors and rear washer hose.
4. Install the splash shield.
5. Install the right front wheel.
6. Lower the vehicle.

the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal

1. Disconnect the battery ground cable (14301).
   
2. Raise and support the vehicle.
   
3. Remove the RH wheel (1007).
   
4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
   
5. Remove the windshield washer reservoir top bolt.
   
   
6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
   
7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
   
8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
   
9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
   
10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.
    
    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.
    
    
11. Loosen the two windshield washer reservoir side bolts.
    
12. Remove the windshield washer reservoir by sliding it out of the side slots.
    
13. Remove the windshield washer pump.
    
    Installation

To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).

I blieve it's the same pump taht runs the rear and front washers.

The windshield washer comprises the following parts:

• Windshield washer reservoir, below the front left-hand fender
• Washer pump, on the outside of the washer reservoir
• Two washer nozzles on the hood/bonnet, adjustable.

---------------------------------------------------------
Windshield Washer Pump and Reservoir Removal
All vehicles

1. Remove the windshield washer reservoir filler neck.

1. Raise and support the vehicle. For additional information, refer to Section 100-02 .

1. Remove the right-hand fender splash shield (wheel shown removed for clarity).

1. Remove the washer reservoir.
   • Disconnect the electrical connectors.
   • Pull off the hoses.

1. Remove the windshield washer pump with rubber gasket (shown with reservoir installed).
   1. Disconnect the electrical connector.
   1. Disconnect the hoses.
   1. Lift out the pump.