Question about 1998 Ford Explorer

1 Answer

No power to hubs

I HAVE A 2003 FORD FX4. WHEN YOU ENGAGE THE 4 WHEEL DRIVE YOU CAN HERE THE TRANSFER CASE ENGEGE, BUT I AM NOT GETTING ANY POWER TO THE HUBS.CAN YOU HELP LARRY

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 61 Answers

Lary,
A possible problem is the cv axle. cv axles ar eknown for going out on those Explorers. Check them and contact me for further assintance.

Posted on Jan 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Which direction does the hub turn to engage


some models do clockwise and some couterclokwise, i do have 2002 F-250SD 4WD that do clokwise.

Feb 05, 2010 | 2002 Ford F250 Super Duty SuperCab

2 Answers

I have a 2000 4wd tacoma with manual locking hubs and the 4wd does not seem to be engaging after locking the hubs and shifting the lever into 4 hi or 4 low


Sounds like one of your hubs is sticking and not engaging. You can check them by engaging the hubs and the transfer case and jacking up each front wheel independently if it doesn't spin your good, if it does you found your problem. As far as fixing a hub goes, it may be just dry and need some grease, or there are some very good aftermarket hubs available from Warn.
Hope this helps

Dec 08, 2009 | 2001 Toyota Tacoma

1 Answer

1988 ford ranger push button four wheel drive an it wont engage all the wires are good it just clicks when u push the button.. what should i look for to make the four wheel drive work again it wont...


Start out with buying yourself a $25 book from the Parts House. The I would go to the front HUBS, secure & safety vehicle before you do anything, Clean, Inspect, Lune & Repair front Hubs as required, get the brakes while you're there. Check your drive line, axles, u-joints etc. Clean , repair , replace as needed. Check for Tranfer case Operation. Is there power going to the front Axle when 4WD is engaged? do you feel a change when you engage the Transfer Case? Have you checked the Power on the circuits? Have you Manual or Auto-locking Front Hubs? Answer all those Questions & read before you do anything.

Nov 03, 2009 | 1988 Ford Ranger

2 Answers

Is it right for your front drive shaft to turn by hand when in park


i'm assuming you have a 4 wheel drive. If that is the case then yes cause when your in two wheel drive mode the front is in neutral

Oct 16, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

03 fx4 supercab transfer case engages, but no front wheel pull


Sounds like the front wheel hubs are not locking in.

Sep 11, 2009 | 1999 Ford Ranger SuperCab

1 Answer

How to shift into 4wd


Ford has 2 types of 4x4 system engagement. One is a knob on the dash that you just turn to 4wheel drive high or low. The other system is the 4x4 transfer case shift on the transmission tunnel (hump) between the driver and passenger seats. To shift into 4 wheel drive high while driving, just let off the gas and shift transfer case into 4H position, and continue driving. To shift into 4 wheel drive Low, stop the vehicle completely, put transmission in neutral, shift transfer case into 4Low position, put trans. in gear, and start driving. I am assuming before doing the above, you have locked in ( turned the front hubs to 4 wheel drive position.) Any further questions, let me know.

May 16, 2009 | 2003 Ford F150 Regular Cab

1 Answer

2004 Ford F-150 extended cab FX4. 4WD problem


Your front hubs are automatic locking hubs, and the gears are hard nylon. These hubs break very easily, therefore causing you to lose your front wheel drive in 4 high, or 4 low. If you replace the hubs with "WARN (name brand) " manual locking hubs, you will never have the issue again. Of course, you will have to get out of the truck and manually lock the hubs, but they are metal gears, and much more durable. I've personally seen the issue several times, and changing the hubs has resolved the issue every time.

May 01, 2009 | 2005 Ford F-150

2 Answers

2004 Ford F-150 extended cab FX4. 4WD problem


The malfunctioning part in my case is what ford calls the "integrated wheel end" which locs the weel hub on the four wheel drive in or out as need. Part is available from Ford and cost about $110.00. I will do this repair myself.

Apr 08, 2009 | 2004 Ford F150

1 Answer

Ford F150 lost 4 wheel drive 2003 FX4


Take the hubs apart, inspect them, and clean them, especially the one that you heard a clunk, something might have broke in the automatic hub lock. Make sure everthing gets put back exactly the same, or you'll have more problems. If that doesn't work, then there is something wrong somewhere in the transfer case.

Mar 15, 2009 | 1999 Ford F150 Regular Cab

Not finding what you are looking for?
1998 Ford Explorer Logo

Related Topics:

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...