Question about 1998 Volkswagen Jetta

1 Answer

Wher is the slave cylinder  an jetta 2.0 1998 for clutch

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 124 Answers

Go to the following website to view where and how to remove and install a Slave Cylinder:

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800b0594

Hope you see what you are your looking for! Good Luck!
If you have any more problems let me know.

Thank you for using Fix Ya!

Don't forget to rate the overall satisfaction of this answer!

Posted on Jan 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Symptoms low clutch fluid


The clutch fluid is also your brake fluid. If it is low then you have a leak somewhere, could be your slave cylinder, or even brake pads are low

Feb 09, 2014 | 2001 Volkswagen Jetta TDI

1 Answer

Where is the clutch auto adjustment located at on a 98 manual Volkswagen jetta?


you most likely have a hydraulic clutch, which the clutch master cylinder is located on the firewall on the driverside close to your drivers side windsheild.it takes brake fluid to fill dot brake fluid will fill it properly. however if your slave cylinder on the transmission is leaking,this will require a replacement of the clutch slave cylinder. look for leakage under passenger side,,just under or below passenger side seat onto ground. recommend if you replace the clutch slave cylinder,you also replace clutch master cylinder located on the drivers side firewall at wind sheild.look under the car while someone pumps the clutch in and out,if you see brake fluid leaking under car onto ground or inside onto carpet at brake pedal,you have a bad clutch master cylinder. recommend you replace both slave cylinder and clutch master cylinder. this will save you lots of time and headaches. thank you for choosing fixya.com

Sep 24, 2011 | 1998 Volkswagen Jetta

1 Answer

I installed a new clutch master cylinder on my 2003 jetta but i cannot find the bleeder valve to bleed the system. any thoughts? thanks


Trace the pipeline to the SLAVE Cylinder down on the transmission. The bleeder valve has to be there on the slave.

Hope this helps you

Please find time to rate me.+

Jun 28, 2011 | 2003 Volkswagen Jetta TDI

1 Answer

Clutch cable ajustment


You have a hydraulic clutch. If the clutch is not disengaging with full pedal, you probably have air in the line. This is usually caused by a leak in the slave cylinder that reuns the reservoir dry. Check in the engine compartment near the brake reservoir for a clutch reservoir and check the fluid level there. Also check for a leak at the slave cylinder. Let us know if you have more questions.

Sep 17, 2010 | 1996 Volkswagen Jetta

1 Answer

Wher i s slave cylinder loc ated on 1998 doge


inside the bellhousing it is a slave and clutch bearing release collar all in one...

Oct 24, 2009 | 1998 Dodge Dakota

1 Answer

95 v.w. jetta 3 4 cyl. clutch adjustment ????


there is no adjustment. may have failed hydaulic master or slave cylinder. also I would try bleeding 1st they may have opened system when they did clutch.

Mar 23, 2009 | 1995 Volkswagen Jetta

Not finding what you are looking for?
1998 Volkswagen Jetta Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...