Question about 2000 Ford F150 Flareside SuperCab

1 Answer

My 2000 F-150 has reverse but no drive, 1st or 2nd gears.

My wife's truck has been having problems with her transmission for about two months. You can put it in gear and it barely moves forward. I have been keeping an eye on the fluid to make sure it had the correct amount and not to over fill the crank case. Do you think it is a sensor, because I still can go in reverse. If so, where is the sensor?

Posted by on

  • eandb4404 Jan 30, 2009

    Yes, I think you're correct because the fluid is not bright red and today it was harder to put into reverse. Good Job, thanks

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 56 Answers

It sounds like you may have to pull the trany >>Tork converter problems << it takes less pressure to go in reverse than forward on a automatic>> pull the tranny pan replace the filter in side change oil and filter about 40 bucks look for shavings on old filter if there are some save the old filter to show the mechanic that is going to make the repairs..
pull the dip stick does the oil smell burnt this is another clue

hope this helps please leave great feedback

Posted on Jan 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will only start in 2nd ,reverse in 1st drive past 1st left will not change gear


Hi, Sounds like a transmission problem. Have it checked out by a qualified mechanic. Could also be a electrical fault. Most transmissions are or have electric parts and sensors to keep it running. (computer controlled) Good luck.

Mar 30, 2015 | 2005 Mercury Grand Marquis

1 Answer

Why won't my Clio automatic engagew 4th gear


How many miles? Have you ever serviced the transmission? f so and recently could be your throttle positioning sensor

Aug 28, 2014 | Cars & Trucks

2 Answers

Buick rendezvous gear shifts just fine but car won't move. No grinding shifting is smooth and flawless vehicle just will not move forward whether it is in drive, 1st, 2nd, or third gear. Reverses and


Sounds as if forward driving gears are shot. Different gears make vehicle move in reverse. I would ask if transmission fluid level when checked is in the operation range or full.

Nov 07, 2013 | Cars & Trucks

1 Answer

2003 chevrolet cavalier, manual transmission lost 2nd, 4th and reverse but still has 1st, 3rd and 5th gears.


Sounds like one of the levers inside the transmission is either broken or otherwise disengaged. Remove the shifter to see if you can see any obvious reason.

Aug 25, 2012 | 2003 Chevrolet Cavalier

1 Answer

99 Saturn SL2 gears


Hello
You will need to have an experienced technical drive this before attempting any repairs, but my gut feeling is that you will need to rebuilt the transmission. That takes many special tools and a high degree of skill and training and is not something that really can be done at home with common hand tools.

Jun 22, 2012 | Cars & Trucks

1 Answer

On a 2001 Chrysler town and country the transmission will go in park, neutral, reverse and will drive in either drive, 3d or 1st gear. The problem is that it won't shift from 1st gear to second or third...


sounds like you are looking at a rebuild. chrysler transmissions need to be adjusted periodically by a qualified tech. if they aren't adjusted properly the results can be catastrophic.

Dec 18, 2009 | 2008 Chrysler Town & Country

1 Answer

Only runs in 1st and 2nd gear and reverse.


This is a fault mode in which the transmission either loses electrical power or the PCM deactivates all of the electronics. The transmission will default to max line pressure. The driver will have Reverse and 3rd, with manual 2nd available by putting the gearshift in 2 or 1 (doesn't matter). 1st, 4th, and TCC lockup will not be available. It will not hurt the car to drive it like this for short periods, but use manual 2nd to get the car moving, and be aware that the trans will generate more heat than normal while operating in limp-home mode due to increased torque converter slippage during 2nd gear starts and no lockup in 3rd gear.

Trans shifts into gear harshly, car feels sluggish off the line
, No 1st, 4th or TCC lockup available, Manual 2nd, 3rd and Reverse are only available gears, CEL is on: Transmission is either in limp-home mode or has lost electrical power. If there are lots of error codes in the PCM, check the under hood fuse that powers the transmission, and if it pops again, look for a short in that circuit like an O2 sensor harness touching exhaust. Otherwise, check PCM codes for a particular fault in the transmission causing the PCM to put it in limp-home mode.

No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter : ShiftA solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Car goes into gear but feels very sluggish like the brakes are dragging, but it will roll easily (starts out in 4th gear), you manually shift to 2 to get it moving, once it's moving you put it back in OD and the car shifts 3rd to 4th on its own and locks the converter at the appropriate time: ShiftB solenoid failed: Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Dec 14, 2009 | 2006 Hummer H3

1 Answer

Won't come out of 4 low and won't change from 1st to 2nd gear


try checking your auto trani fluid... and with the 4 wheel drive try puting ti in nuteral and if the doesnt work try puting it in reverse and back up after taking it out of 4 wheel drive.

May 24, 2009 | 1996 Ford Bronco

1 Answer

Transmission on 1995 Buick Century, slipping badly


Sir I would first change my filter. When you do you should be able to acertain if anything is wrong by what yuo find in your pan. I think your clutchs are probably bad, but with out being able to scan it I don't have any other ideas. I have been lucky a couple of time before and changing the filter solved my problem. Your car is in limp mode generally you have reverse and second gear. 1st gear and reverse use the same clutches, so I am wondering if maybe you have second gear only!

Dec 26, 2008 | 1995 Buick Century

Not finding what you are looking for?
2000 Ford F150 Flareside SuperCab Logo

211 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

67911 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22011 Answers

Fordexpert

Level 3 Expert

5367 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...