Question about 2004 Ford Expedition

1 Answer

Replace front brake pads on 2000 expedition

Are there any special tools needed to replace front pads.
Are there any special tricks in removing the rotors or the pads such as hidden locks, clips, or key ways .
i'v done the brakes on other makes but never a Ford Expedition

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 4,369 Answers

Just a toex head tool for the caliper pins

Posted on Feb 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i compress the caliper piston back of audi a6 2000 2.8l awd what kind of tools i need . Vise grip is not working.


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also.
But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!

For front brake pads. You should buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!!

Check brake fluid level and top up if neccessary!!!

Oct 26, 2011 | 2000 Audi A6

1 Answer

Remving caliper pins on 2000 vw jetta and caliper


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
For front brake pads. You should buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Jun 26, 2011 | 2000 Volkswagen Jetta TDI

1 Answer

I need to change the front brakes on a 2001 BMW Z3 3.0...any special tools required for that? I've done lots of brake jobs, but never on a beamer...thanks!


NOPE NO SPECIAL TOOLS JUST REMOVE BRAKE PAD WEAR INDICATOR CONNECTOR.REMOVE THE CALIPER GUIDE BOLTS AND THE SPRING CLAMP.TURN UP THE CALIPER AND REMOVE THE BRAKE PADS.THE INNER PAD IS LOCATED WITH A SPRING IN THE PISTON.

Oct 25, 2010 | 2000 BMW Z3

2 Answers

Cannot get calipers off FORD


BRAKE HOSE BOLT IS STILL CONNECTED YOU HAVE TO LOOSEN AND REMOVE BRAKE HOSE BOLT BEFORE CALIPERS COME OFF.THE COPPER WASHERS THAT CAME OUT WITH BRAKE HOSE BOLT HAS TO BE REPLACED THEY ARE SEALS THEY WILL LEAK IF REUSE THEM.

May 30, 2010 | 2004 Ford Expedition

1 Answer

Front brakes on a 2005 Jeep Rubicon


Once you take the caliper bracket off, the rotor should just fall off. If the Jeep stops without any vibrations I would leave the rotors alone., unless they are scored badly from brake pads worn out and metal to metal.

Mar 19, 2010 | 2005 Jeep Wrangler

1 Answer

How to replace front brake pads for a 2000 expedition


raise and support the front ,remove both tires , there is two bolts on the backside of the caliper,I find it easier to pry on the back pad to drive the piston so you can wiggle the caliper off,do not let the caliper hang by the hose look at both sides of the rotor if they have groves they need to be turned if they are ok then you need to push the piston back into the caliper use a c clamp(loosen the bleeder valve on the caliper it makes it easier) put the pads on the rotor then put caliper back on and thighten bolts. repeat on other side. ( might pay to get a repair manuel if you have any doubts)

Feb 03, 2010 | 2000 Ford Expedition

1 Answer

I'm trying to replace my front pads there are 2


Replace left and right brake pads at the same time. Do not replace brake pads for one side of the vehicle only.
  1. Raise and support front of vehicle.
  2. Remove tire and wheel assemblies.
  3. Remove pad pins and springs.
  4. Remove brake pads, then shims.
  5. Reverse procedure to install. When installing new brake pads, push caliper piston inward using piston compressor No. 490221600C or equivalent.

nothing Special that I see

Jul 14, 2009 | Mazda 323 Cars & Trucks

4 Answers

Replace rear brake pads on a 2000 grand marquis


rate as fixya if this is what you need. Thanks

  1. Remove the rear disc brake caliper (2K327).
  2. Remove the brake caliper bolts.
  3. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2B582).
  1. sya~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pads.
    Remove the brake pads by pushing inward and rotating the pad up.
  1. NOTE: Use a block of wood or used pad to protect the piston and boots.
    Retract the caliper piston (2196) into the rear disc brake caliper.
cf7b02c.gif

Mar 15, 2009 | 2000 Mercury Grand Marquis

2 Answers

Brake rotors


They get rusted to the hub. Try heat and a large hammer.

Nov 25, 2008 | 2003 Ford Expedition

1 Answer

2000 Silvrado z71 4wd Brake Pad Replacement


crawl underneath the front and look at the caliper if it has a duel piston caliper you will see 2 circles about 3 inches across and if it is a single piston caliper it will only have one of these circles in the middle this iswhere the pistons are. yes those pads are suitable. As for bleeding the brakes you need to start at the passengers side rear wheel and bleed it first then go to the drivers side rear wheel then go to the passengers side front wheel and then finally the drivers side front wheel. If you are only replacing the brake pads and shoes then you don't need to bleed the brakes. If you are bleeding the brakes then you will want to be sure to top up the brake fluid as you are doing thebleeding process as if you don't you will end up having to start all over again. as for special tools you may need a 3/8 hex bit and a 8 inch " C " clamp to compress the calipers after you remove the brake pads. If you are replacing the rotors you may require a special socket fo dis-assebleing and re-assembly of the front hubs.

Oct 05, 2008 | 2000 Chevrolet Silverado

Not finding what you are looking for?
2004 Ford Expedition Logo

Related Topics:

555 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...