Question about 2000 Chrysler Town & Country

1 Answer

Chrysler 2000 town and country says it's the tcm

Ok my local stattion takes the car to a transmission place who wants to "rebuild " the transmission because the TCM is bad.  Is the tcm even in the transmission? Or is located utside the transmission?  $2100? arghhhh

Posted by on

  • 1 more comment 
  • Anonymous Mar 13, 2014

    It has a 2.4 4cyl. motor and front wheel drive. It will not go into reverse.

  • Anonymous Mar 13, 2014

    wont go in reverse

  • Anonymous Mar 21, 2014

    tcm on a 2007 chrysler 300 need the location

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 362 Answers

Here's the location of the transmission control module.
chrysler 2000 town and country says it's the tcm - 4a2cf9b.png

Posted on Jan 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Chryser Town and country - First to send gear bump, bump grab.


Then you have an internal transmission failure from poor workmanship on the rebuild.

Oct 28, 2012 | 2003 Chrysler Town & Country

1 Answer

Error code 0700 aa1 aa2


Hi there:
The DTC P0700 is a Information Code The Transaxle Control Module (TCM) that monitors the malfunction of sensors and actuators relating to transaxle control. If any malfunction is detected, the TCM informs the PCM by sending a signal (P0700 code). P0700 means that a code has been set in the TCM.
This code is for information ONLY. If this code is present, check for transaxle codes. So basically, the P0700 code is telling you to check the TCM for a transaxle DTC. The TCM can not turn on the check engine light so it has the PCM do it, which can only be done with a diagnostic scanner. The self retreival method for chryslers with the ignition key will not pull up the specific transmission fault codes in the TCM.


Hope this helps.

Mar 30, 2012 | 2001 Chrysler Town & Country

1 Answer

I have a 2001 town & country 3.8l lxi and the speedometer goes crazy jumping from 0 -120 and then back again. When this happens the car starts jumping if you try to drive it. I changed both sensors...


The PCM does not calculate the speedometer the TCM does.Most of the time if is not a bad output speed sensor it is the connector.You can purchase a replcement connector from the dealer or a local transmission supply house.Also you must have the correct tire size(Pinion factor) programmed into your TCM and this will need to be done with a professional scan tool.

May 03, 2011 | 2001 Chrysler Town & Country

1 Answer

Ok i have a 2001 chrysler town and country service engine light came on took it to auto to see what codes came up and one of them is po731,p1775,p0700. i need to now where the tcm is and i also need to...


These are all transmission codes there located insde the trany under oil pan Probably olny one one of them in stuck or bad But you realy should have this done at a transmissoin shop and also have them change filters do a complete service on it to there becase when they go there not cheap to rebuild

Nov 16, 2010 | 2002 Chrysler Town & Country

1 Answer

I recently had transmissions swaped out of my 1996 chrysler town and country and i dont think the mechanic swapped out the transmission is there a way to check the V.I.N. or somthing to see if he really...


then u have one of tow things wrong, the TCM (Transmission Control Module) or defective or the wiring to the transmission is defective,remember this transmission is controlled electrically. have the TCM tested by the dealer with the special scanner they use to pick up electrical issues.

Jul 29, 2010 | 1996 Chrysler Town & Country

1 Answer

2000 Chrysler Town & Country smelling fuel


check the fuel filter connections first. If all ok, have a mechanic check it. If there is an evaporative leak, the check engine light should be on.

Jul 24, 2010 | 2000 Chrysler Town & Country

1 Answer

Code p1698 town & country 96 fail the emission test


p1698 code=No CCD message from TCM or No Transmission Bus Messages
It means the person's computer could not connect with yours.it's possible it was his problem if your not having any issues


Dec 04, 2009 | 1996 Chrysler Town & Country

1 Answer

Rebuild chrysler trans town and country 3.8


ok, you want to rebuild one or you need to know if you could rebuild one?

Oct 12, 2009 | 1998 Chrysler Town & Country

1 Answer

Check engine light on 2005 town and country 3.3


(DTC) CODE # P0700....Transmission Control System (MIL Request)

Translation:
Transmission Control Module (TCM) Malfunction or Failure.

P0700 Information Code

The Transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. If any malfunction is detected, the TCM informs the PCM by sending a signal (P0700 code). P0700 means that a code has been set in the TCM.

This code is for information ONLY. If this code is present, check for transaxle codes.


P1776: Solenoid Switch Valve Latched in Low/Reverse Position. The TCM monitors the L/R solenoid to ensure that the fluid transfer happens. It uses a Pressure switch to verify this. Usually this code is set by a switch that is stuck or a solenoid that is not mechanically operating.

A transmission shop would be better suited for this type of work.

Apr 11, 2009 | 2005 Chrysler Town & Country

Not finding what you are looking for?
2000 Chrysler Town & Country Logo

Related Topics:

1,404 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...