Question about 1999 Dodge Intrepid

2 Answers

Wiper motor does not work on my 1994 dodge intrepid?

Where can i get a diagram on how to replace the motor.

Posted by on

  • yadayada
    yadayada May 11, 2010

    that would be in a factory service manual.



2 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 21 Answers

(I made images larger at the end of instructions)

See Figures 1, 2 and 3
wiper motor does not work on my 1994 dodge intrepi - 0900c1528006ad4a.jpgFig. 1: Unbolt the wiper motor from the housing 0900c1528006ad4b.jpgFig. 2: A little maneuvering may be requirewiper motor does not work on my 1994 dodge intrepi - 0900c1528006ad4c.jpgout 0900c1528006ad4c.jpgFig. 3: Exploded view of the wiper motor and associated components that make up the wiper system

  1. Disconnect the negative battery cable.
  2. Remove the wiper arm and blade assemblies, then disconnect the in-line hose connections. Do not discard the in-line connectors.
  3. Remove the rear hood seal with the cowl top plastic screen. Disconnect the washer hose in-line connectors.
  4. Disconnect the motor wiring harness at the back side of the housing.
  5. Remove the four wiper housing module mounting screws, then remove the housing.
  6. Remove the nut and disconnect the wiper drive linkage from the motor crank.
  7. Remove the three motor mounting screws. Lift the motor and mounting plate out of the housing.
  8. Disconnect the motor harness grommet from the housing.
To install:
  1. Assemblethe linkage to the motor. Make sure that the crank fits over the D sloton the motor shaft. Tighten the mounting nut to 90-106 inch lbs. (11-14Nm). Be sure the motor is still in the park position before assemblingto the linkage; if it is not, temporarily connect the motor to thewiring and operate the switch to park the motor before assembling thelinkage.
  2. Position the wiper motor and install the retaining nuts until snug.
  3. Attach the linkage drive crank to the motor crank arm.
  4. Plug the wiper motor wiring back together.
  5. Install the wiper motor cover.
  6. Install the wiper arms and plastic cowl removed previously.
  7. Connect the negatiwiper motor does not work on my 1994 dodge intrepi - 0900c1528006ad4a.gif check the wiper motor for proper operation.

Copyright © 2002 Delmar, All Rights Rwiper motor does not work on my 1994 dodge intrepi - 0900c1528006ad4c.gif src="" alt="0900c1528006ad4b.gif" class="h_mi" />
Copyright © 2002 Delmar, All Rights Reserved. 0900c1528006ad4c.gif
Copyright © 2002 Delmar, All Rights Reserved.

Posted on Jan 30, 2009

  • Lady_Chaos
    Lady_Chaos Jan 30, 2009

    dang it, it didn't post the photos....grrr. here is the link and info (hopefully the url will work out)...


  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a 2000 dodge caravan 3.0 L engine. I have a problem with the wipers. When I turn on the switch, the motor seems to be activated but the wiper arms do not move. Can anyone shed any light on what my problem may be.

Posted on Feb 10, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have an 02 Dodge Intrepid whose blower motor will continue to run after I turn the ignition off.

Will the wipers also work with the ignition off? If so, possible ignition switch problem. If wipers don't work, suspect shorted blower motor resistor or controller

Sep 05, 2015 | 2002 Dodge Intrepid

1 Answer

I have 1995 DODGE INTREPID, THE WIPER motor is working but the arms are not moving ,how do i repair it

take off the panel that covers the wiper linkage and reconnect the motor linkage.

Sep 29, 2012 | Dodge Intrepid Cars & Trucks

1 Answer

98 dodge intrepid wipers when turn on only swings on once and then it stops

Try putting a jumper wire from ground to the wiper motor. Simply touch the motor with a ground wire to test. If motor starts to move and run normally -that was issue. Now to fix -run a ground wire from wiper motor to firewall as a permanent fix - good clean connections are key.

Apr 11, 2012 | 1998 Dodge Intrepid

1 Answer

20003 Intrepid - My wiper washer fluid and motor quit working.

Your wiper motor most likely burnt out. And your washer fluid pump did the same.

Oct 13, 2017 | 2003 Dodge Intrepid

1 Answer

1994 Dodge Dakota wipers wont work. New motor. need wiring diagram to trace. Power to motor but has open field.

try the earth connection or fit your own and try not to get too technical because you will confuse yourself

Aug 29, 2009 | 1994 Dodge Dakota Club Cab

2 Answers

Wiring diagram of window wiper motor on 1994 Mercedes Benz 320

hello,can you post your chassis number,so i could help you regarding your wiper motor,because 1994 model have different version,ty

Apr 15, 2009 | 2007 Mercedes-Benz R320 CDI

1 Answer

1994 dodge spirit wiper problem

bad wiring or just old wiring between everything

Mar 15, 2009 | 1994 Dodge Spirit

1 Answer

2002 intrepid wipers

well check to hear if you hear the wiper motor working if you do look at the arm take the end cap off loosen the bolt if you here the motor running/tighten them bak up if you do not here the motor check fuse under the dash and inthe engine compartment and replace fuse or fuses/ please rate my response thank you very much

Jan 28, 2009 | 2002 Dodge Intrepid

1 Answer

97 dodge intrepid wipers not working

My Chevy was having troubles with the wipers and had to put a large zip tie around the motor and wiring connection. The post were worn down just enough for it to lose contact. The Zip Tie holds tension on it.

Jan 26, 2009 | 1997 Dodge Intrepid

Not finding what you are looking for?
1999 Dodge Intrepid Logo

847 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides