Question about 1992 Honda Accord

1 Answer

Replacement of passenger side headlight assembly 92 honda accord

I need to lower bumper so I ca n remove defective assembly. Where are the bolts to drop bumper on that side?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

The bolts are at the fender and bumper edge from the corner feel the underside its a 10mm bolt just take it out the rest are retainers/ Please rate my response thank you very much

Posted on Jan 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to take passenger headlamp out of 328i bmw 2008 so it can be replaced?


2008 328i Passenger headlight assembly removal.

The headlight assembly is held in by 4 "star" bolts (size 25); 2 visible on the top of the assembly, 2 not visible or easily accessible.

The 2 bolts not so visible require that the front half of the wheel well come off and the front bumper or "nose" of the car.... The bumper is what needs to come off, but there are 2 bumper bolts hidden by the wheel well.

The wheel well is held in by 7mm bolts, 2 of which are actually bolted to the bumper on the bottom.

The front bumper is held on with 7mm bolts on the bottom edge, and star bolts, size 25, accessible on the top edge. (Hood open). Here were my steps.

1. Jack up the car on the side you are replacing, remove wheel.
2. Using 7mm socket, remove all the bolts to peel off the front half of the wheel well. With the wheel well out, you can see the 2 other star bolts holding the headlight assembly, but you can only remove one of them... even if you were good enough to get both removed, the headlight assemble will not push out through the bumper.... Keep going with bumper removal.
3. Remove 2, 7mm bolts of the front bumper that are now visible up near the outer edge of the headlight assembly.
4. At this point I removed the bumper's top edge start bolts and bottom edge 7mm bolts about 3/4 of the way across the bumper...
5. The bumper is very flexible and you can now pull it back , reach in, and get that last difficult star bolt on the headlight assembly....
6. Don't forget the one electrical connector....
7. I also recommend testing the new assembly by plugging it in before removing anything

Nov 09, 2012 | Cars & Trucks

2 Answers

How do i change my headlight assembly on a 2001 honda accord


HEADLIGHT REPLACEMENT

1. Remove the front bumper
2. Disconnect the connectors (A).
3. Remove the 5 mounting bolts (B), then remove the headlight assembly (C).

Fig. 21: Removing Mounting Bolts & Headlight Assembly
6_26_2012_3_27_45_pm.jpg

Jun 24, 2012 | 2001 Honda Accord

2 Answers

Need to change the passenger side headlight


This video will show you how to change the headlight in your Accord.">

May 19, 2010 | 1996 Honda Accord

1 Answer

Can't replace passenger side headlight on 4 cylinder sedan because of obstruction from what appears to be part of the emission control system (a plastic funnel assembly). Can't free the three screws...


  1. Remove the front bumper.
  2. Disconnect the connectors (A).
    1. Remove the five mounting bolts (B), then remove the headlight assembly (C).
    2. Install the headlight in the reverse order of removal.
    3. After replacement, adjust the headlights to local requirements.

Nov 07, 2009 | 1999 Honda Accord

1 Answer

Headlight removal for 1996 honda accord wagon


in case this has not been solved, you will need to remove the retaining clips, screws and bolts from the underside of the car. remove the left and right turn signals, in addition there are 2 bolts on each side of the bumper in the turn signal area, lift and gently pull forward to remove, re assemble as you have taken apart, best of luck, thanks

Feb 18, 2009 | 1996 Honda Accord

2 Answers

Bumper cover removal


Its easy look at the bottom of the bumper has retainers and the fenders have a bolt on each side then just slide off

Jan 23, 2009 | 1991 Honda Accord

1 Answer

How can I change the headlights in a 1998 Honda Accord?


Its not that hard but you have to remove bumper to get to the two bottom bolts that holds the headlights. First remove grille and there are 2 10mm bolts that holt the tip of fenders they are the first bolts under the fender weld closes to the bumper cover. Then there are two bumper mounts/brackets that hold bumper to frame/radiator support. they are held by (4) 12mm bolts may need a swivel socket to get to them( easily accessed if you remove front signal lights in the bumper held by philips screws in the corners).After removing bracket bumper should come right off. Headlights are in plain clear view. (4) 10mm bolts and you are done. Re-install in the reverse. Good Luck . If I fixed ya leave me a FIX-YA comment. Contact me if you need more info

Dec 10, 2008 | 1998 Honda Accord

2 Answers

Headlight replacement


you doo not need to remove the bumper...the rt side is a bit tighter than the left side though..on the back of the headlamp are plastic screw retainers..they turn 1/4 to 1/2 turn to unlock the headlamp bulbs.( you could remove the battery to do this..it will certainly give you more room.) once you turn the lock grab the bulb and pull it straight back , unplug it and plug the new one in. be careful not to touch the new bulb glass with your fingers as this can get oil on the surface and create a "hot spot" which can lead to premature failure!

Oct 16, 2008 | 1992 Honda Accord

1 Answer

1996 accord headlight replacement


hi you have to remove the bumper but not a big job as it is only the cover a screw under each wheel arch three clips in the middle and a set of clips and ten millimeter headed bolts yates210456

Sep 20, 2008 | 1996 Honda Accord

2 Answers

Headlight replacement


Remove the bumper. If I remember correctly, it is two bolts each side, which you can reach from the front with an extension on your ratchet. Don't forget to unplug (and perhaps remove) your front turn signals.

Jun 30, 2008 | 1991 Honda Accord

Not finding what you are looking for?
1992 Honda Accord Logo

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...