Question about 1993 Jeep Grand Cherokee

1 Answer

1993 Jeep Grand Cherokee Laredo turn signals stopped working.

At first they started to blink irregular (slower & pause) then they just stopped working. I changed the fuses & bulbs and they still don't work but the hazards do?

Posted by on

  • patricia greer Feb 21, 2013

    grand cherokee laredo 1993 myturnsignal was working when i would mess with the nob that you moove up and for the turnsignals to go right or leftthe green light would come on but not no more they will not work at all and that is the only thing not working and they would blink realy fast to and i also want to let you no that i have hazzard lights and headlights and parking lights break lights backup lights like i said everything else worys so could it be the switch or a fuse please tell me thankyou

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,011 Answers

Your multifunction switch in the steering column needs to be replaced this is very common.normally the job cost about$ 275.00

Posted on Jan 29, 2009

  • wendy M Mar 19, 2012

    give the azard lights a few flicks or spray with lubricant, as they accumulate dust etc from lack of use and if connected to indicators will stop them working, worked for me.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Left signal not working nor does the green arrow


PROBLEM WITH THE CURRENT CABLE SIR. THANKYOU

Jan 03, 2010 | 1993 Jeep Grand Cherokee

1 Answer

1993 jeep laredo auto shutdown& fuel pump relays go crazy open & close it wont stop and car dont start


Most often a relay will act like a buzzer if it is not properly grounded. The ground signal generally comes from the computer. The auto shutdown realy feeds the fuel pump relay and therefore is shutdown relay isn't getting the proper signal it will in turn send same improper signal to pump relay. I am sending you a decent diagram of this and suggest you first make sure all body grounds are clean and secure.
http://www.scribd.com/doc/18999822/Jeep-Wiring-2
Good luck!

Dec 09, 2009 | 1993 Jeep Grand Cherokee

1 Answer

Turn signals and ac stopped working at the same time


don't know if they are related. as for the turn signals check the flasher. there should be 2 of them.one for the turn sinals the other for the emer. flashers

Mar 11, 2009 | 1999 Jeep Grand Cherokee

2 Answers

1993 JEEP GRAND CHEROKEE LAREDO IM TOTALLY BAFFLED


Back up a minute...Do you have spark from the coil wire? (juice from coil) If so, change or check rotor and cap (wires do not all go bad at same time so unless they are wet, likely at least good enough to start engine)

Mar 05, 2009 | 1993 Jeep Grand Cherokee

1 Answer

1993 JEEP GRAND CHEROKEE LAREDO- TRUCK WONT


OK...I have a 93 outside...one diagram I have shows an ignition module next to coil...but there is none on mine, (4.0 engine)
Two items to check are crank sensor and cam sensor inside distributor. Test procedure can be found in just about any manual including haynes.
You will need a decent volt/ohm meter to do testing. You can also check codes by turning ignition switch on/off three times, leaving it on the third time. Check engine will flash code #'s (ex: one flash, pause two flashes= the number twelve.then followed by a longer pause then another set of flashes etc.)

Mar 05, 2009 | 1993 Jeep Grand Cherokee

1 Answer

Diagnostic display will not stop blinking


You have lost the keep alive memory, either the radio is defective or the fuse for that circuit is burned out.

Nov 21, 2008 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
1993 Jeep Grand Cherokee Logo

322 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...