Question about 2001 Chevrolet Blazer

1 Answer

Drivers door need alignment

The door is drooping.

Posted by on

  • 1 more comment 
  • mr_n_mrs_moe Jan 29, 2009

    can you send a pic to show me.

  • Blazer Owner Mar 18, 2009

    The driver side door of my 2001 Chevy Blazer is off and causes the door not fully close. If you slam it as hard as you can from the outside it sometimes works. Could it be the hinge? Do I need to replace the enitre door? Because it is off that caused the interior panel to seperate from the door from pulling so hard. Any suggestions... other than bring it to the dealer?

  • Jenna_138 May 05, 2009

    I have the same problem with my Blazer, except my drivers side door fell off! My boyfriend is a welder, so he just welded the pin to the hinge. Its working but now the hinge it going. I just love my door! its a quick fix if it helps.



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 2,920 Answers

You will need to put in new hinge pins in the top hinge.they sell them at the auto parts store and all you hav to do is tell them whats going on with the door sagging and they will sell you what you need

Posted on Jan 29, 2009

  • Ronnie Houston Jan 29, 2009

    i dont have a pic to send but the auto parts store will know exactly what to sell you and they will even tell you how to put it in



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2007 golf r32 last weekend the car started and then immediately stopped with immobiliser active reading on the dashboard the battery is fully charged and both keys have new batteries.

Sounds like the tiny transponder in your keys has failed.or dropped.out while your changed /checked batteries. Small glass bead about 2mm diameter and 8mm long. Check where you drooped it ?
Or reset the keys. Driver door open, Key in the ignition, and press.and hold all buttons u.til tiny red light on keys ( pin hole youve probably not noticed before) lights up and flashed to pair after 5seconds press open door. Then close and open again keep driver door open. Repeat with second keys.
Should fix it.

Jun 11, 2017 | Cars & Trucks

1 Answer

2006 LR3 Land Rover, rain and water in the floor of driver. how go in ? how fixed. lot of water..

It can come in underneath, through the floor. Also the cables that go between the door pillar and door can permit water to pass, if they are not sealed correctly.

May 21, 2012 | 2006 Land Rover LR3

1 Answer

Driver door needs to be align. Can I do it myself?

If the door wont line up correctly, is most likely due to bad hinge pins. Open door try to raise up on outside of door near bottom. If it has play hinge pins need to be replaced.

Jul 09, 2010 | 2001 Chevrolet Blazer

2 Answers

The drivers door will not close fully even if you push it real hard it really never will click into that lock position

open the door loosen the striker on the door jam and adjust it by slidding it back and forth, also if the door has drooped a little loosen the lower hinge and put a 3/8 shim between the hinge and door!!!

Nov 24, 2009 | 1990 Chevrolet K1500

1 Answer

Window on driver side of 2003 Camry stuck. Had

You can adjust the door latch by aligning the male and female portion of each. This can be adjusted by loosening the screw and aligning it. And finally when aligned, tighten the screw. Unless otherwise if the door hinges are loose, such that the doors are misaligned, then, you have to replace the door hinges. Or put a bushing at the door hinges to keep it
aligned. This will correct the defect.

Nov 15, 2009 | 1992 Toyota Camry V6

1 Answer

2000 Impala drivers side window not aligned

You took window out???you need to take door panel off and align the window regulator, if thats what you took off. if you didnt touch anything in the door, then the regulator may have a problem.

Oct 12, 2009 | 2001 Chevrolet Impala

1 Answer

The drivers side door on my 93 mustang is not fitting right making it hard to close and open the door. I have to lift it to open or close

check the door hinge pins and make sure they are fully seated. Also check the hinge pin bushings - they are made of bronze and if they wear out, the door will droop

Apr 20, 2009 | 1993 Ford Mustang

1 Answer

Driver's door adjustment

in order for someone to help you tell us what you are driving
car, truck what
2 door or 4
we would be guessing as make the adjustment on the bottom hinge on the door

Nov 30, 2017 | Jeep Grand Cherokee Cars & Trucks

1 Answer


Trim generally does not have much to do with body sealing. Check to make sure that the rubber door seals are intact and are actually touching the door frame. Make sure your door is properly aligned in the frame. Sometimes the hinges wear and cause some drooping. If condition is not severe, sometimes you can "fatten up" the door gasket by sliding a length of rubber hose inside it. As far as trim goes, most trim on Jeeps is glued on.
Good Luck

Nov 11, 2008 | 2005 Jeep Grand Cherokee

Not finding what you are looking for?
2001 Chevrolet Blazer Logo

Related Topics:

164 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides