Question about 1995 Mercury Villager

2 Answers

1994 mercury villager

I have a problem with my 1994 mercury villager i changed the thermostat on it but it still runs hot what i want to know is how do i bleed the system

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

If the car is stilling running hot check the antifreeze overflow bottle for a crack and to answer your question start the car and get it to normal temp while it is still running you open the overflow bottle fill it to the cold mark and keep adding coolant until all the bubbles are out of the system and put the cap back on right away

Posted on Jan 29, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Mercury Master
  • 6,674 Answers

Start with engine cool. Remove rad cap, top up coolant, start engine, & turn on heater (not defrost). let it run until up to normal operating temperature & radiator fan comes on, then shuts off. Let it do this about 3 times before you put rad cap back on & top up return bottle to proper level. Every once in a while, rev engine slightly for a few seconds while your doing it, to speed up bleed by increasing flow. Keep an eye on temperature gauge for too hot, and fan not coming on, if so, shut it off.

Posted on Jan 29, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Replaced thermostat and top hoses and it continues to run hot

have you listened to make sure the fans are engaging?

May 03, 2011 | 1994 Mercury Villager

1 Answer

I got 1994 mercury villager I put in a new thermostat in and sometime I got heat from about 20 mins then there in just cold air coming out.I flush it all out I dont know what to do now can you help me...

That's becaue you have air trapped in the system. very common.

Start engine cold with radiator cap loose and let it run until upper hose is hot (meaning thermostat opened) and it can burp air. Keep radiator & resevoir full. Shut off engine, fill radiator, tighten cap, let coolant get sucked out of reservoir into radiator.

IF still can't burp, go to a shop with evac/fill equipment to usck all air out and fill with vacuum method.

It helpas to jack up front of van as ahigh as you can get it. Air is trapped in top of engine cylinder head ecause i is higher than radiator cap,

go here for more help


Jan 17, 2011 | 1994 Mercury Villager

1 Answer

What is the right thermostat position of a 94 mercury villager

use only Ford or Nissan themostat. has a small hole at top. Must be there.

go here for help. Villagers hard to bleed air out after refill of cooling system

Dec 08, 2010 | 1994 Mercury Villager

1 Answer

2002 villager a/c started blowing hot and also running hot. I changed thermostat and leaking hose, but did not fix problem. What else could it be? No sign of leakage.

u cant tell by sight-must hav pro leak test--evaporator may be problem-is passenger floor wet--compressor cud hav failed also

Sep 01, 2010 | 2002 Mercury Villager

1 Answer

Where is the thermostat located at in the engine compartment of the 2000 mercury villager

passenger side (rt) of engine, middle. Be ery careful tightening the bolts so you don't break the pipe. Locate thermostat with jiggle valve facing up.

It is very hard to bleed air from system when refilling. see files if you don't have heat when done.

go here too

Housing Removal
  1. Drain the cooling system; refer to Cooling System Draining, Filling And Bleeding .
  1. Remove the upper radiator hose.
    1. Remove the hose clamp bolt.
    1. Remove the hose clamps.
    1. Remove the upper radiator hose.
  1. Remove the water bypass hose.
    1. Remove the clamps.
    1. Remove the bypass hose.
  1. Remove the thermostat housing.
    1. Remove the bolts.
    1. Remove the thermostat housing.
  1. syv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not reuse hose clamps. Make sure new hose clamps are seated correctly.
    NOTE: Make sure the thermostat housing and mating surface are clean of dirt and old silicone.
    NOTE: Apply a 2.0-3.0 mm (0.079-0.118 inch) bead of Silicone Gasket and Sealant F7AZ-19554-EA or equivalent meeting Ford specification WSK-M2G343-A4 to the mounting surface of the water pump.

Jan 09, 2010 | 2000 Mercury Villager

1 Answer

1994 mercury villager has skip and engine service

Try disconnecting the battery for 2 hours. Then drive for 10 miles so the PCM can relearn. It may run rough for 10 miles.

If not ok, go to Villager website for expert team help free. Check files, ask questions

Oct 31, 2009 | 1994 Mercury Villager

1 Answer

1994 mercury villager fan not working

The fan is control by a thermostat.
When the radiator reaches about 200 degree F. it should turn on.
If it do not turn on then it either the thermostat is bad or the fan.
When you turn the air condition on then the fan should also turn on.
Start with the cheap part which is the thermostat.Then work for there.

Mar 10, 2009 | 1995 Mercury Villager

2 Answers

No heat

if you replaced the thermostat, you have an air bubble trapped in the engine. So, you don't have any coolant running through the heater core, therefore no heat.
sometimes hard to "burp" air bubble. Try this. Park park facing uphill and jack up front of car too. You want to get radiator opening higher than top of engine. Then remvoe radiator cap (cold engine), fill radiator, then fill coolant reservoir to full point. Install radiator cap but leave it loose so air can escape. Start engine until upper radiator hose going into radiator is hot. This should burp air. Repeat a few times while adding coolant mix (50/50 antifreeze) to keep radiator full. Be careful not to remove radiator cap when engine is hot.
lwt us know how ou make out. There is a more complicated procedure but you need tools and knowledge of where air bleed is on top of engine

Jan 03, 2009 | 1998 Mercury Villager

Not finding what you are looking for?
1995 Mercury Villager Logo

360 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts


Level 3 Expert

74241 Answers


Level 3 Expert

5426 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides