Question about Hyundai Tiburon

1 Answer

2003 dodge ram code po 700

Will not shift from 2nd to 3rd

Posted by on

  • cbrotherrock Jan 29, 2009

    My 2003 dodge ram is a 1500 4 door 5.7 4x4.When the problem happened I was towing a empty car trailor weighing about 1,000 lbs.I was driving on flat ground under no load at about 50 mph and I

    heard a clunk noise almost like when you have a tourque convertor that is shifting in and out of overdrive, At the same time the engine light came on. I pulled over and stopped then I took off and it shifted from 1st to 2nd then when it tried to go into 3rd it would just raise the rpms but not keep the truck moving.



    When I put the truck into 2nd gear manually it would stay 2nd gear.I dont know alot about these transmissions but the truck has always shifted fine with no flare ups or sighns of any problems at all.I find it hard to beleive that it would be anything other than a electrical problem but then again you never know. any help with this problem would be greatly appreaciated Thank You.

  • Ronnie Wilson May 11, 2010

    No Engine size or Chassis Info as in Ram 1500 2WD or 250 4WD ETC. Sometimes this Makes A Big difference



    I'm not so sure as the References I Have are Vague in Answering my "NO 2-3 UPSHIFT" Symptom although Everything Pointing at TCM Transmission Control Module. So it could be that or a Modulators Solenoid or shift Solenoid

    Maybe this will help you or w/ more Info I Can Help More

    SYMPTOM
    P0700-TRANSMISSION CONTROL SYSTEM (MIL REQUEST)

    WHEN MONITORED
    Ignition on and battery voltage greater than 10 volts .

    SET CONDITION
    An active DTC is stored in the TCM. One Trip Fault. Three good trips to turn off the MIL

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,596 Answers

The Manual Shift "WORKING" is a Good Sign , In Older Models this would Point to Vacuum Modulator Let Me Do Some Diggin and Maybe Come Up with A Sureshot Hit on EXACTLY what it is Im sure its Relased to A Electronic Modulation od TCM

Posted on Jan 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Ram van. Why isn't transmission shifting?


Nathaniel, Check transmission fluid level and top up if required.
It does sound like a problem with shift solenoids, and should be checked and diagnosed by a good transmission tech.

Apr 20, 2016 | Dodge Cars & Trucks

1 Answer

92 dodge ram 150 not shifting


Two things happen on the Dodge's. 1. the rear O2 sensor shorts out and meses things up. 2. the Inner seal on the Direct drum (3rd) shrinks and causes a delayed up shift.

Aug 05, 2008 | 1996 Dodge Ram 1500 Club Cab

1 Answer

Transmission won't shift from 2nd to 3rd on 2003 Dodge neon


Have you had someone check the computer for trouble codes ?

Aug 04, 2015 | Dodge Cars & Trucks

1 Answer

2003 dodge intrepid will not shift into third


It sounds like the TCM has reverted to Safe Mode because it has detected a problem.

http://www.obd-codes.com/p0700

Aug 22, 2012 | 2003 Dodge Intrepid

1 Answer

97 dodge ram 2500 van doesn't shift on time from 2nd to 3rd and 3rd to 4th.


it could be any number of things, i would try having the transmission serviced first. the transmission filter could be getting clogged making it work harder and therfore making it shift differently.

Jun 21, 2010 | 1998 Dodge Ram

1 Answer

What is the most common cause of an error code: 0040 and 0041 in a 2003 dodge ram 1500?


no such codes, it would be something like a po 441 or po 045. recheck your codes,good luck.

Oct 28, 2009 | 2004 Dodge Ram 1500

1 Answer

Code po700 problem


First thing, smell your fluid to see if it smells burned. The code po 700 is a trans. control problem code, which could be because of burned clutches, but I don't really think that's the case. The best way to tell if you have an internal trans problem is to drop the pan and see if there's a lot of debris in the pan. If there is a lot of junk in the pan, more than likely you'll have to have the trans. rebuilt. I would take it to a dealer and have them run a trans diagnostic on it. With their scan tool, they can check your clutch volumes, turn all your sensors off and on to tell you what your problem is. Hope this helps. Phil

Jan 20, 2009 | 2002 Dodge Ram 3500 Truck

1 Answer

1999 dodge ram delayed and erratic shifting


ummm i would say you need to adjust your trans shift cable, check your fluid level, and the problem i had with my dodge was similar to yours... it was my 3rd-4th actuator spring, it had broke and couldnt hold the pressure to keep it in gear

Oct 07, 2008 | 1999 Dodge Ram

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

367 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

68038 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22011 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6817 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...