Question about 1987 Toyota Xtracab

2 Answers

Turn signals and wipers don't work but high beams and curise cont

Wipers and turn signals will not work but the high beams and curise control still work on switch and fuses are good in passenger side area! Hey I've got an '87 Toyota and was driving when suddenly the wipers stopped working and the turn signals won't go on and the display on my am radio in the cab is flickering in and out in sync with a ticking noise I'm hearing which sounds like the turn-signal noise.

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 41 Answers

Sounds like you may need a blinker relay possibly a multi-switch

Posted on Jan 29, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 61 Answers

Check your charging system the voltage at the battery should be 12.85 Volts WITHOUT the engine running and 13.2-14.5 Volts with the engine RUNNING. If the voltage is low it probably means the alternator is at fault.

Posted on Jan 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1984 chevrolet silverado high beams lights works and low beam lights, turning lights, emergency light and brakes lights don't work. I need help!


Those lights are on different circuits. The high and low beam lights are powered thru the headlight switch, the turn signals, brake, and hazards go thru the turn signal switch.
I would want to know if each circuit has power at the switch that controls it.

Jun 28, 2013 | Cars & Trucks

2 Answers

The 2004 Nissan Sentra I own intermittent wipers don't work. Can anyone tell me how to fix them?


The intermittent function for your wipers is controlled by the wiper control amplifier. This is an integral part of the wiper (combination) switch and is serviced only by replacing the switch assembly.

Nov 26, 2011 | 2004 Nissan Sentra

1 Answer

I have a 1996 Jeep Cherokee. Headlight Problem: Year ago? Switched on high beams, complete darkness (low beams don't work at the same time I've come to find out). Solution: Don't turn on...


ok, first ,, check all the bulbs again, and *** make sure that your hands never touch the actual bulb, these lights will turn the oils from your hands into cooking grease when it comes to these bulbs and cause them to blow out much to early on in their life span, , next,, Pull the light switch ( high beam switch towards you for a quick flash of the head light high beams,, if this doesn't make the high beams come on, your problem is going to be in the switch itself ( what your calling the high beam/turn signal lever) before going to that extreme though,, if you have a junk yard near you, go pull one of the relays off a junked vehicle, and stab it into your system one at a time, it could be something as simple as a relay heating up and disconnecting prematurely due to heat ,, if you don't have a junk yard that you can grab a relay,, here is a link that shows how to check them, But its time consuming http://www.youtube.com/watch?v=C8t25GjZ6i4&NR=1

Aug 10, 2011 | 1996 Jeep Cherokee Sport

1 Answer

On a 2002 dodge ram 1500 truck the brake lights and the turn signals and winshield wipers dont work the only brake light that works is above the cab. and the turn signal flashes on the dash like they are...


I suspect a bad multi function switch located in the left hand side of the steering column. This switch controls your high/low beams/wiper delay/windshield washer/turn signals and hazards.

Dec 31, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

Turn signals and wipers don't work but high beams and curise cont


Your switch is bad and needs replaced.... even if parts of it works doesnt mean that its not bad

Jan 25, 2009 | 1995 Buick Regal

1 Answer

2001 Pontiac Firebird has turn signal problem


The turns,hazards, high/ low headlamps, possibly cruise cont. and wipers, are all operated by the "multifunction switch". Replace it and you should be good to go. I hope this helps.

Dec 02, 2008 | 2001 Pontiac Firebird

1 Answer

Turn Signals and High Beams are not working and I have checked the fuse what else could it be? Everything else is working


Sounds like the combination switch is bad. The comination switch is for the turn signals and high beams and sometimes cruise control and windshield wipers. The combination switch is the turn signal lever. Also might want to check turn signal flasher operation.

Sep 12, 2008 | 1997 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

173 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...