Question about 1984 Chevrolet S-10

1 Answer

1984 S10 wiper arms

How do i get my windshild wiper arm off of my 1984 chevy S10? I cant figure it out

Posted by on

  • brad
    brad Jan 28, 2009

    thanks I will try it tomarrow

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,990 Answers

No Problem! Look down on the Bottom of the Wiper Arm, wher it attaches and Swivels. There is a Small tab that comes off of the Upper Part of the Arm that looks like Two Front Teeth Sticking up just a Little. Take a Pair of Pliers and Pull this Tab Up Towards the Top of the Winshield to Release the Lock on the Arm. then take a Pair of Pliers with Tape on them so that you will not Scratch the Arm and Pull while you Wiggle the Arm right at the Swivel Pont and they will Come off. Please Rate my Response, I need all the Help That I can Get! Thanks!

Posted on Jan 28, 2009

  • Travis Humphries
    Travis Humphries Jan 28, 2009

    Let me know if you have any Problems!

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 92 chevy S10 truck, how do you remove the wiper blades and arms?


GM S10/S15/Sonoma Pick-Ups 1982-1993 Repair Manual Blade and Arm - REMOVAL & INSTALLATION
(see Figures 1, 2 and 3)
  1. Matchmark the base of the wiper arm to the linkage. This will assure the arm is installed in the proper position. If the arm is being replaced, transfer the matchmark from the old component to the new one before installation. This can be done by placing the new arm on top of the old one and copying the mark.
1bb2352.jpg

Fig. 1: Removing the wiper arm using J-8966

0234572.jpg

Fig. 2: If no wiper arm tool is available, use a small prytool to depress the spring

5227e24.jpg

Fig. 3: With the spring released, pull the wiper arm from the linkage
  1. Most wiper arms are retained by a spring clip. Some are equipped with a release tab at the center which should be depressed to release the arm. If no tab is provided, use a small prybar or a wiper arm removal tool such as J-8966 to depress the spring and release the arm. Remove the arm from the vehicle.
  2. Some late model vehicles (all 1993 and some earlier models) are equipped with a wiper arm that utilizes a small release hole at the base of the wiper arm. If equipped, insert a 1 / 8 in. drift pin into the tool access hole to release the locking device and allow the arm to be easily pulled from the transmission. If necessary, use a gentle rocking motion to remove the arm.
To install:
  1. Except for late model vehicles equipped with the tool access hole, align the matchmarks and gently press the blade over the linkage and snap into position.
  2. For 1993 vehicles (and earlier models equipped with the access hole on the arm) straighten the arm assembly and insert the pin. Align the arm with the linkage mark made earlier, then press down on the arm's head casting until it seats and locks onto the wiper pin. Remove the drift pin.
  3. Operate the wipers and verify proper alignment.

Hope helps (remember rated this).

Jul 08, 2010 | 1992 Chevrolet S-10

1 Answer

How do you remove the windshield wiper arms


The wiper arms have a push in tab at the very bottom at the fitting that is pressed into the wiper linkage below the screen. Use a flat headed screwdriver to pry out the tab. Once out the arm can be pulled right off. Now you can remove the cowling screen

Apr 07, 2010 | 1987 Chevrolet S-10 Pickup

1 Answer

How do I take a wiper arm of off the rear window of a Toyota celi


this either has a nut on the base of the arm that needs to be removed or if no nut. then pull the arm away from the glass and there will be a meatal tab at the base of the arm that will slide to the side with this slid to the side the wiper arm is unlocked and will pop right off

Jan 12, 2010 | 1984 Toyota Celica

2 Answers

As I was driving my 92 Dodge Dakota with the wipers on, I heard a sound and they stopped moving. I can hear the motor running. Do you have a suggestion for this and what parts might be needed to fix it?


had the same problem with mine all you need is a windshild wiper bushing it bout 5 to 10 $ at auto zone there are about 2 or 3 bushing that may need replacing mine was simplest one the one on the motor its easy it justs snaps onthe motor arm and than to the arms of the windshild transmistion

Oct 15, 2009 | 1992 Dodge Dakota

1 Answer

Remove and replace wiper blade assebly 89 chevy silverado


there is a keeper on the inside of the arm. its easier to get to if you remove the whole arm. lift the wiper arm and near the pivot point there is a little flat bar that sticks out along the arm itself. its about a quarter inch long. pull that out alittle and slide the arm off the peg. makes it easier for me. if you cannot get the wiper off still, destroy it. your replacing it anyway and the arm is pretty sturdy.

Jun 03, 2009 | 1989 Chevrolet K1500

1 Answer

Windshield wipers


You might have a stripped wiper arm spline. Check it by seeing if it moves with your hand. Also check wiper arm connection under the black plastic unscrew and remove black plastic.

May 06, 2009 | 2000 Mazda MPV

1 Answer

1984 chevy S10 windshild wipers


at the arm remove the cap on end and their is a nut remove it 10 mm / Please rate my response thank you very much

Jan 28, 2009 | 1984 Chevrolet S-10

1 Answer

Windshild wipers stuck on 96 ford explorer


go to bottom of arm take end cap off loosen bolt / Turn on wipers Check to here the motor if its running if its running turn off and tighten up the bolt wiper arm at bottom then turn the wipers on if you here the motor running if you do not check fuse under dash and in engine compartment / Please rate my response thank you very much

Jan 28, 2009 | 1991 Buick Park Avenue

2 Answers

My 2001 Buick Regal driver side wind shield wiper arm is stripped, it wipes at random. Please help


i don't know what you mean by stripped, but iam gessing you mean it won't stay on the windshild when it wipes. have you tride another blade? if not i would try that first. if that dosent work you may have to try another wiper arm. all wipers will do what yours is doing when conditions are just right. you can minamise this problem maybe with a double wiper blade. hope this will help. OLD SCHOOL.

Jan 10, 2009 | 1996 Buick Regal Olympic Gold

1 Answer

Wipers seized- motor works. cant move blades more tham1=2 inches.


you have to remove the whole wiper arm both sides...under hood remove 5 -5/16 screw from vent panel .. remove panel .. under panel on drivers side you will see where arm attach to wiper motor ..remove nut... then remove 3 bolts that hold wiper motor to firewall .

Nov 29, 2008 | 1988 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

258 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...