Question about 1991 Acura Integra Hatchback

1 Answer

Timming belt water pump

Does anyone have a diagram on this problem

Posted by on

  • Dave Real
    Dave Real May 11, 2010

    Do you need a picture of the timing marks? And is it the 1.8 engine?

  • Anonymous Mar 30, 2014

    Timming belt

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 90 Answers

timming belt water pump - 009aac0.jpg1af38b2.jpg
you will have to save to file then zoom in to read.

Posted on Jan 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Timming belt broke from water pump broke while driving car put new water pump on n timming belt but car doesnt start right plus shakes doesnt sound right 2001 neon dodge


Sounds like timing belt not on correctly. Check timing marks are aligned correctly when installing timing belt. This vehicle should have 2-3 marks to be aligned when installing belt.marks should be on cam gear/ crankshaft gear and intermediate shaft if engine is equipped with it.

Sep 10, 2011 | Dodge Neon Cars & Trucks

1 Answer

CODE P0016 CAM /CRANK CORRELATION SENSOR WHAT COULD CAUSE SENSOR TO GO BAD WE INSTALLED NEW TIMMING BELT ,IDLER & TENTIONER PULLY AND WATER PUMP


there you go the timing is off:

http://www.obd-codes.com/p0016

alignment for timing:

http://www.2carpros.com/diagrams/toyota/avalon/2003

Apr 19, 2011 | 2003 Toyota Avalon

1 Answer

Got the water pump on, but it wont let the water flow through, is it possible i put the belt on wrong


don't know as I am not there but here is a website the will let you know if you did, Hope it helps Tim:


http://www.2carpros.com/diagrams

Apr 16, 2011 | Dodge Nitro Cars & Trucks

2 Answers

Is it necessary to take the timming belt off to replace the water pump on a 1996 isuzu rodeo


3.2L engine, you will have to remove timing belt to replace water pump, your water pump is timing belt driven, I would replace timing belt while in there, good luck, hope this was very helpful.

May 14, 2010 | 1996 Isuzu Rodeo

1 Answer

Whinning Noise when cold.


Timing belts don't while because they don't slip! Could be the water pump/alternator belt.

Dec 12, 2009 | 2006 Suzuki Swift

1 Answer

Do i need to change the water pump when i change the timing belt?


most people change the water pump when doing the timming belt because most of the stuff you take off for the belt also has to come off for the water pump. the water pump is a easy job on most cars once the items around it are removed

Nov 15, 2009 | 2002 Daewoo Leganza

1 Answer

Cam shaft timming marks 1999 Daewoo 1.6 liter


there is a special tool to hold gears in correct place on some of these models, but you can hold one cam at a time with a spanner then feed belt on exhaust cam then inlet cam gear
get someone to hold gears in place while you feed belt on.
the inlet cam is more prone to turn off mark more than exhaust.
if you have tensioner that needs retaining pin in when installing
you fit belt while aligning timming marks
fit tensioner as last spot to feed belt on with retaining pin in adjuster
get correct tension on belt by turning water pump so that you can flex (turn) belt 90 degrees only just while using finger and thumb
tighten water pump check flex
check all timing marks are correct
remove retaining pin from auto tensioner
turn motor over a couple of turns by hand observing tensioner arrow should hover around V mark and that all timing marks align up again(after one complete turn)

Aug 02, 2009 | 1999 Daewoo Lanos

1 Answer

How do you replace a water pump on a 94 ford escort?


the water pump is even further in than the timming belt.in fact the pump pulley is driven by the timming belt. however with a shop manuel its not bad of a job to do, just go slow
good luck chris

Mar 19, 2009 | 1994 Ford Escort

1 Answer

HOW TO INSTALL A TIMMING BELT ON1991 VOLVO740


REMOVED ALL BELTS, WATER PUMP FAN, SHROUD AND PULLEY.
REMOVE TIMING COVER REMOVE CRANK SHAFT PULLEY.
. PUT ENGINE IN TOP DEAD CENTER SO YOU CAN SEE TIMING MARKS. REVERSE PROCEDURE. GOOD LUCK

Nov 04, 2008 | 1990 Volvo 740

Not finding what you are looking for?
1991 Acura Integra Hatchback Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...