Question about 2002 Toyota Celica

1 Answer

Door panel removable

I was wondering if you have like a diagram of how to remove the door panels.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

Well you should not need a diagram First look for screws or little caps in the trim look under the arm rest / take out the screw / then take of mirror cover/ than pull out bottom of door panel and slightley around edges look cor screws with cover on the side or retainerswith little pins in the middle then pull form the bottom upward and then disconnect the wiring on door and you should have your door off/ Please rate my response Thank you very much

Posted on Jan 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the diagram for the door panel for 2007 suzuki xl-7?


the door, what door?
look here
https://suzukipitstopplus.com/Products/1059-2006-grand-vitara-xl-7-owners-manual.aspx

or alldata.com

or buy a real FSM.

there are like 5 diagrams. which one.
windows. ?
locks
the door size draiwings.
door card , removals.
collision solutions.
mirror service?

all this is in the FSM
the factory service manual, if serious diy , get one, and not wonder.

Jul 06, 2014 | 2007 Suzuki XL-7

1 Answer

How do i take off the inside drivers door panel on a 2005 dodge caravan


Hi Roberta, here's the instructions on how to remove your door panel. I have to wonder though on why you are removing it, my guess is you window doesn't roll up or down and your replacing the regulator. Any way here goes.

REMOVAL

  1. Remove the plug and remove screw attaching door pull cup to inner door panel.
  2. Remove switch bezel and disconnect power window/memory switch.
  3. Remove screws attaching trim panel to door from below map pocket.
  4. If equipped, remove window crank. (Refer to 23 - BODY/DOOR - FRONT/WINDOW CRANK - REMOVAL)
  5. Remove screw holding door trim to door panel from behind inside latch release handle .
  6. Disengage clips attaching door trim to door frame around perimeter of panel.
  7. Lift trim panel upward to disengage flange from inner belt molding at top of door.
  8. Tilt top of trim panel away from door to gain access to latch linkage.
  9. Disengage clip attaching linkage rod to inside latch release handle (INSIDE DOOR HANDLE LINKAGE).
  10. Separate linkage rod from latch handle.
  11. Disconnect the power door switch, courtesy lamp electrical connectors.
  12. Remove front door trim panel from vehicle.
Hope this helps and have an awesome day Roberta!

May 21, 2014 | 2005 Dodge Grand Caravan

1 Answer

Fuse diagram


no one fuse, check the connections for switch, one may have been knocked loose. does lock open manually and is it hard? actuator may have failed or rubbing and resisting . hope this helps

Jan 11, 2014 | 2003 GMC Sierra 2500HD

1 Answer

How do I remove the passenger side door panel from a 1994 Chevy S10 pickup??


hi there

there will be phillips screw on outside of door panel and usually one where handle is once removed all of them you pull pull gently and there will be pastic rivet clips that you have to get loose once all are loose lift upward and remove from door have a wonderful day thank you

Aug 22, 2011 | Chevrolet S 10 Cars & Trucks

2 Answers

How do I remove the left rear door panel from a 1996 Nissan Maxima? The window just fell down. It can be manually lifted up, but it slides back down again. It no longer mechanically works. If you can...



  • Disconnect the negative battery cable(for safety if you have power locks and windows)
  • At the bottom of the door panel remove the two screws
  • Pry up at the front edge of the power window switch pod and lift it out then unplug the electrical connector
  • Remove the inside door handle
  • Remove the screw in the door pull pocket
  • Pull the door panel away from the door far enough to disconnect the electrical connectors

May 23, 2011 | 1996 Nissan Maxima

2 Answers

To replace window switch for driver window, must I remove the whole inside door panel on drivers door ? Are there diagrams available online to remove the interior panel ?


YOU DONT HAVE TO REMOVE DOOR PANEL.ALL HOLDING SWITCH A SCREW THAT GOES THROUGH SWITCH INTO DOOR HANDLE.REMOVE THE SCREW PRY AND PULL UP THE SWITCH.

Jun 04, 2010 | 1995 Chevrolet Lumina

1 Answer

Need diagram of how the LH inside door panel is removed 1996 S-10


Consult a chiltons or haynes repair manual. May review the layout assembly under applicable year model from lmctruck.com

Jan 15, 2010 | 2002 Chevrolet S-10

1 Answer

Diagram for replacing exterior door handles


ok. first u remove the door panel(s), with the window rolled up, u will be able to see the back side of the exterior door handle. there will be three bolts, they are size 10metric. there is also a rod attached to the handle held in place by a plastic clip, remove the rod, then remove the three bolts. from the outside remove the exterior door handle being careful not to scratch painted surface. Repeat for the other door(s). Repeat this for installation.

Dec 14, 2008 | 1997 Toyota Camry

1 Answer

Remove the Passenger side door frame on a 2002 Ford Explorer


    Lift up on the switch plate until it snaps out ,remove the bolt from under there and the bolts along the bottom of the panel. There may be a few others so look around. When all are removed lift up on the door panel(DO NOT pull towards you it will destroy the panel). Your mirror is now accessible.

Nov 28, 2008 | 2002 Ford Explorer

1 Answer

Drivers side widow will not go down more than 2 inches


A) Remove the screws in the following locations:
  1. Door handle
  2. door grip
  3. Middle of panel, 3/4 down the panel from the top
B) Removal of door Handle

  1. Use caution
  2. Slide the door handle in the direction of the motor
  3. The door handle is now freed from the door
C) Partial removal of door panel
  1. Insert a dull instrument into the port that is located on the panel roughly half way down the panel and the side the furthest from engine.
  2. Carefully pry the panel loose.
  3. With your hands, remove the panel by its contour. There are roughly 10 or so plastic plug
D) Tricky Part; Removal of door Handle

  1. Free the door handle from the panel, by carefully pushing it through the panel on an angle...
  2. You can now push the panel up beyond the door lock button.... then...
  3. The wiring haness is now exposed.
E) Wiring Harness

  1. You now un plug the wiring harness from:
  • Door handle
  • Lower courteosy light
  • Electric window controls (three wires)
F) Final steps

  • Lift the panel up and over the door lock button.
Now to your window problem.

When I examined the problem that I had with my Odyssey, I found the following:

  1. Two bolts were missing;
  2. The other tow bolts were lossed;
  3. The motor had shifted positions.





Nov 15, 2008 | 1995 Honda Odyssey

Not finding what you are looking for?
2002 Toyota Celica Logo

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...