Question about 1998 GMC Jimmy

1 Answer

Will shift to 4 wheel low and back to 2 wheel hi but not 4 hi

It blinks both 4 wheel hi and low then remains in 2 wheel hi

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Transfer case motor on drivers side or first check atc fuse under hood

Posted on Jan 31, 2009

  • rollin1320 Feb 01, 2009

    remove ground cable on battery for 5min then replace or the vacum switch on top drivers side of trans

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 GMC yukon xl slt transfer case drops out of 2 wheel hi but will work in auto 4 wheel


There is a transfer case control computer in the dash on the left side around the headlight control,they will cause the blinking lights and not shifting.

Mar 30, 2014 | 2005 GMC Yukon XL

1 Answer

Surburban won't shift into 2 wheel hi insteads ends up in 4 wheel low


if its manual shift then inspect the linkage, if its push button then the motor/servo on the transfer case could be the issue. or the switch. i had to chase a simular issue on my tahoe and it ended up being the motor on the transfer case that selects the gears

Mar 13, 2012 | 1999 Chevrolet Suburban

1 Answer

When drivingtruck in 2 wheel drive the 4 wheel low light will flash and when slow truck down to a stop it will shift into 4 wheel low and will not go back to 2 wheel high


Sometimes the solenoids will stick on the axle neither in 2 or 4 wheel drive, if this problem started when you weren't shifting between two and four wheel drive it is probably the push button switch cluster on your dash going bad

Dec 12, 2010 | 2000 Chevrolet Blazer

1 Answer

Will not go into 4 wheel low


Make sure you have it in (N) before shifting it. Did it work before?

Apr 10, 2010 | 2000 GMC Sierra

2 Answers

1996 chevy blazer will not go into 4wd hi but it will go in to 4wd lo. when you push the 4 Hi button it just flashes and then does nothing.


The major components to this system are a shift control motor that is mounted to the transfer case, and a shift control module that is behind your center console. since the transfer case is still shifting into 4wd lo, the shift motor is still moving somewhat, so the most likely cause is the shift control module, but there isn't an easy way to troubleshoot between the two...

Nov 16, 2009 | 1996 Chevrolet Blazer

1 Answer

I put my 2000 escalade in 4 wheel low last night; and now I cannot get it switched back to 2 wheel high. I will not go above 50 miles an hour when I drive it. When I press the 2 wheel high button it...


start truck leave in park press 2 wheel high button put truck in drive move truck,check for being in 2 wheel high, if still in 4 wheel low have switch and shift solenoid checked

May 17, 2009 | 2007 Cadillac Escalade Two-Wheel Drive

2 Answers

2001 Dodge Durango stuck in 4 wheel-Low. Won't switch back to 2WD


Just to clarify, the "transmission" is not stuck in 4-Lo. It is the "transfer case" that is attached to the transmission that actually engages the 4-Hi and 4-Lo modes. To properly shift your vehicle into 4-Lo, you know that you have to shift the transmission into neutral and slow down to less than 5 mph. Once your vehicle slows down to this range, your can switch your transfer case into 4-Lo mode. Due to the inner workings of the transfer case, the actual shift into 4-Lo may take a few seconds to complete. This is normal and does not signify that there is an issue. All transfer cases that have 4-Lo mode will act this way regardless of the make or model. To make a long story short, to shift out of 4-Lo you must follow the same steps that you took to shift into 4-Lo, just in reverse order. Switch the transfer case to 4-Lo mode if it isn't already there. Slow down to less than 5 mph (your vehicle must be moving, though). Then, shift your car into 4-Hi or 2WD. Give your vehicle several seconds to complete the shift. The transfer case indicator light will flash until it is complete. When it does complete the shift into the new gear mode, you will most likely hear a "clunk" (the range sleeve inside the transfer case disengages from its mating spline) from under your car. Again, any transfer case with 4-Lo (regardless of make or model) will exhibit this same noise. This should help you get out of 4-Lo. It is good practice to shift your car into and out of 4-Lo at least a few times each year to keep all of the splines free of corrosion and build-up. Based on the age of your vehicle, your transfer case may also need a complete flush and some new transmission fluid. Hope this helps.

Feb 22, 2009 | 2001 Dodge Durango

1 Answer

Isuzu shift problem


Hi Bob My Rodeo has the same problem. It got alot better after replacing the vacumm hoses to the solenoid on the transfer case. Also stop put it in 4 low then back into 4 high then hit the button it usualy goes right into 2 wheel drive.

Jan 06, 2009 | 1998 Isuzu Rodeo

Not finding what you are looking for?
1998 GMC Jimmy Logo

Related Topics:

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

63575 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...