Question about 2004 Toyota Sequoia

1 Answer

I have a 2003 Sequoia. I need to change the bulb in my break light on the passenger side. How can I do this?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

There are 2 screws in the inside of the light take them out and pull firmley towards you if it doesnt come out the first time jiggle it a little bit and try again they will come out/ Please rate my response thank you very much

Posted on Jan 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Break Light on Passenger Side not working.The running lights all work Fine. All the Blinkers work fine. It is just a break light on passenger side. I bought a new bulb thinking I could not see the broken...


Over time corrosion can accumulated and rust out a tail light socket and render it non-functioning. Yes it can be replaced and in your case for about $6.00. You can find these at most any auto parts store.

In case of a problem or clarification or my solution was insufficient, don't hesitate to post me a reply.

If you are satisfied, rate my solution with the "thumbs" or (even better) add a testimonial.

Jun 08, 2011 | Dodge Durango Cars & Trucks

1 Answer

Need to change headlight bulb in gmc envoy 2003


Drivers side- stick your hand behind the headlight and remove the rubber cover, and twist out the light.

Passenger side- remove the air cleaner top, and move the air cleaner out of the way. You now have complete access to this side to remove the rubber boot covering the bulb.

Dec 22, 2010 | 2003 GMC Envoy

1 Answer

On my 2004 expedition one of the break lights is not working. the parking light work fine, but when I press the break the passenger side break light does not come on. I changed the bulb and that did not...


check the electrical contacts within the bulb fixture for oxidation or damage. Check also the wires and wire harness for damage or connection problems.

Oct 26, 2010 | 2004 Ford Expedition

1 Answer

How do you change the light bulb under the mirror on the drivers sides door?


How do you change a light bulb on the passenger side mirror of a 2006 ford expedition?

May 20, 2010 | 2003 Ford Expedition

1 Answer

Replacing tail light bulbs on 2001 Toyota Sequoia


Remove the two screws holding the tail light cover in place along the edge of the tail light assembly.

After you remove the two screws in the back panel, you have to pull the assembly out towards the side of the vehicle. You cannot pull it straight back from the trunk or you will break the pins that hold the lens cover onto the side of the SUV.

There are two pins that allow the light cover to be secured against the back of the truck. One pin is towards the top, the other pin is towards the bottom.

Twist out the bulb assembly.
Pull out the bulb
Insert the new bulb
Twist back in the bulb assembly
Place the pins over the pin holes in the light cover mold on the side of the truck
Push in gently Replace screws and you are done.

Nov 01, 2009 | 2001 Toyota Sequoia

1 Answer

Head light bulb


OPEN THE HOOD, THE BULB IS HELD IN PLACE BY A ROUND TWIST TO LOCK/UNLOCK RETAINER, PULL THAT BACK AND REMOVE THE BULB BY WIGGLING IT AND PULLING STRAIGHT BACK.
CAUTION, DON'T TOUCH THE NEW BULB, IT WILL BREAK SOON AFTER YOU TURN IT ON FORM THE OIL ON YOUR SKIN, IF YOU DO TOUCH IT CLEAN IT OFF WITH RUBBING ALCOHOL.

Aug 13, 2008 | 2003 Pontiac Grand Am

1 Answer

SIDE MARKER LIGHT, PASSENGER SIDE


Assuming you are talking about the side marker bulb in the bumper, you need to get behind the bumper and un bolt the lens from the back side to change lens or if just bulb replacement twist socket counterclockwise to remove from lens and then change bulb. Keep in mind if the bumper has been hit this will be very difficult to do unless you loosen up bumper and pull out.

Jul 17, 2008 | 2003 Nissan Xterra

Not finding what you are looking for?
2004 Toyota Sequoia Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...