Question about 1997 Jeep Grand Cherokee

2 Answers

No power to the driver door electric window pod

I checked the harness between the door and body ( all good) even tried to activate the window while wiggling the wires. (nothing happened) checked all the fuses under the hood (all look good)
The other electric windows work fine on all the other doors.
Does each door have it's own relay, or breaker?
I don't get any light indicators or door light to come on, as if someone had cut a wire etc..
I checked all the wires under the dash, next to the kick panel that come from the door to the body of the jeep I can't find any loose terminal's or broken wires.
ANY INFO WOULD HELP.

Posted by on

  • Patrick Dennehy May 11, 2010

    I have found broken or damaged wires in Jeep and Chrysler products inside the covered bundle that flexes when the door is opened or closed. Sometimes they are crushed inside the insulation and the fault is hard to see. If you have narrowed it down this far, keep looking in that bundle for the bad ground or hot wire. Unwrap and expose this bundle as thoroughly as you can. You said yourself, the door indicator is not working "as if someone cut a wire.." Have faith, it's there, you'll find it. Good luck, TT

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,201 Answers

If the other windows are operating from the panel on the driver's door, there is power going to the panel. The switch for the driver door window is probably bad.

Posted on Jan 28, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,990 Answers

Check the Fuse Relay Box under the Hood. There Should be Relays for the Windows inside this Box. It is the Small Black Squares. If you cannot find the Relays, LePlease Rate my Response, I need all the Help That I can Get! Thanks!t me Know what is in it.

Posted on Jan 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does the driver's side door electrical harness keep breaking?


The most likely cause of your problem is the master switch in the drivers door. The windows and the locks are on two separate circuits. The only part that these two have in common is the master switch.
Of course it is also possible that the wiring harness between the driver side door and cowl is corroded and that some of the pins are to corroded or even broken off and do not make contact. Also check that you have good and tight positive and negative battery cable connection to the battery posts. Wiggle the cables a bit. If it still does not work, pull out and put back fuse #8 and circuit breaker/relay #68. Try wiggling relay #68 it might just not make good contact or is stuck.
Pulling the fuse or breaker cuts the power and resets the circuit. Good Luck and let us know how it is going.

Dec 03, 2015 | Cars & Trucks

2 Answers

No electric power to left door Fuse and relay are good


Check the wire lume that runs from the body to the door inside a rubber bellow. the wires can break from constant moving and I'm not sure what vehicle you have, but this is a defect for a few vehicles out there the wire can be to short in some cases from cost saving manufacturing. It may be necessary to remove the door panel and remove the harness through the wire opening to be able to move the boot far enough to access the broken wire or even just to check it in some cases.
How I like to repair it, is to put a new wire through the entire pivot point and join it inside the door and body where the wire does not move constantly.

Hope this helps

Mar 04, 2015 | 2007 Saturn ION-2 Quad Coupe

1 Answer

2003 saturn vue driver window does not work took out motor tested works fine no power to motor checked 30 amp fuse good switched out relay with known good one switched out window switch still no power rear...


check for a broken wire in the harness that goes from the body to the door. this is the most common problem as these wire flex every time the door is opened

Mar 03, 2013 | 2003 Saturn VUE

1 Answer

My power windows in driver side and passenger back window wont go up or down.


A master switch may be at falt, but try you may want to check power gets to window motors, remove door panels and use your test lite activate switch and see if lites Ok then needs a window motor if no your master switch is bad..
Very rarely on this year you may also found broken wires between drivers door and vehicle, where harness pass from door to inside car, disconet harnes from inside left kick panel and pull it out towars door pull black rubber boot back remove electrical tape and check all wires if any open or split repair and rechek al over. good luck

Dec 05, 2010 | 1996 Toyota Camry

1 Answer

Electric windows dont move up or down on my honda accord


If the windows don't work, any of several issues is likely to blame, including no electricity, bad switches, bad motor, damaged window regulator, or even a broken wire.

Automotive power windows use a switched motor to operate a mechanical window regulator. This regulator moves the pane of glass into the door.

To check and confirm the fault try this procedure:--

1) Open the fuse panel and check the fuses for disrupted elements. The fuse panel at the driver's side kick panel, or between the dashboard and the door. In some cars the fuses are mounted in the engine compartment, in front of the driver's side firewall. Check the fuses and replace if faulty.
2)
Test the wiring harnesses from the fuse panel to the switches and from the switches to the window regulator motor. If the circuits test fine, then proceed to the next step. If a wiring harness is shorted or damaged, it will need to be replaced.3) Remove and test the switches on the driver's side door panel. Pry them up with a screwdriver and pull them free of the panel's opening. Disconnect the switch assembly from the wiring harness by pulling the adapter plug from the assembly. Test the switches individually by touching both sides of one switch with the circuit tester. Each switch will have two terminals, and if the tester is positive on both terminals while the window is activated, then the switch is good. Replace the switch assembly if any of the switches fails the test. Most power window switches come in assembled modules and cannot be replaced individually.4) Remove and test (if possible) the power window motor. Turn the armrest bolts and interior door handle screws counterclockwise, then pull the door panel free from the pop rivets. Behind the panel are a window regulator, the window glass, and the electric driver motor. The motor is usually located in the lower right section of the door. Unplug the motor from the wiring harness and unbolt it from the window regulator by turning the bolts counterclockwise. Pull the motor straight out, away from the gears. And check out if motor is receiving exact 12 volts at the terminals. If not then either motor is faulty or there is a confirm short if motor is replaced.

5) If all the above mentioned possibilities are checked out ok then the window regulator needs to be checked. Inspect the window regulator's joints for rust or stiff movement, if the electrical system is operating correctly. These joints can corrode or break, causing the window to stop working. With the door panel off, the window regulator can be removed and replaced by sliding the glass away from the track mounts, then turning all mount bolts counterclockwise and manipulating the regulator out of the door.

Thanks. keep updated for any more query.you can rate this solution and show your appreciation.

Sep 16, 2010 | Honda Accord Cars & Trucks

2 Answers

I have a 1997 ford explorer, and it has power seats and power windows.and the windows and seats will not move.all of the fuses have been checked and are good.


If the fuses are checked ok then there is a possibility that either driver door side main switch or the window regulator or the window motor is gone faulty.
If the windows don't work, any of several issues is likely to blame, including no electricity, bad switches, bad motor, damaged window regulator, or even a broken wire.
Automotive power windows use a switched motor to operate a mechanical window regulator. This regulator moves the pane of glass into the door.
To check and confirm the fault try this procedure:--
1) Open the fuse panel and check the fuses for disrupted elements. The fuse panel at the driver's side kick panel, or between the dashboard and the door. In some cars the fuses are mounted in the engine compartment, in front of the driver's side firewall. Check the fuses and replace if faulty.
2) 
Test the wiring harnesses from the fuse panel to the switches and from the switches to the window regulator motor. If the circuits test fine, then proceed to the next step. If a wiring harness is shorted or damaged, it will need to be replaced.3) Remove and test the switches on the driver's side door panel. Pry them up with a screwdriver and pull them free of the panel's opening. Disconnect the switch assembly from the wiring harness by pulling the adapter plug from the assembly. Test the switches individually by touching both sides of one switch with the circuit tester. Each switch will have two terminals, and if the tester is positive on both terminals while the window is activated, then the switch is good. Replace the switch assembly if any of the switches fails the test. Most power window switches come in assembled modules and cannot be replaced individually.4) Remove and test (if possible) the power window motor. Turn the armrest bolts and interior door handle screws counterclockwise, then pull the door panel free from the pop rivets. Behind the panel are a window regulator, the window glass, and the electric driver motor. The motor is usually located in the lower right section of the door. Unplug the motor from the wiring harness and unbolt it from the window regulator by turning the bolts counterclockwise. Pull the motor straight out, away from the gears. And check out if motor is receiving exact 12 volts at the terminals. If not then either motor is faulty or there is a confirm short if motor is replaced.
5) If all the above mentioned possibilities are checked out ok then the window regulator needs to be checked. Inspect the window regulator's joints for rust or stiff movement, if the electrical system is operating correctly. These joints can corrode or break, causing the window to stop working. With the door panel off, the window regulator can be removed and replaced by sliding the glass away from the track mounts, then turning all mount bolts counterclockwise and manipulating the regulator out of the door.
Thanks. keep updated for any more query.you can rate this solution and show your appreciation.

Aug 10, 2010 | Ford Explorer Cars & Trucks

1 Answer

Windows not working


If the windows don't work, any of several issues is likely to blame, including no electricity, bad switches, bad motor, damaged window regulator, or even a broken wire.
Automotive power windows use a switched motor to operate a mechanical window regulator. This regulator moves the pane of glass into the door.
To check and confirm the fault try this procedure:--
1) Open the fuse panel and check the fuses for disrupted elements. The fuse panel at the driver's side kick panel, or between the dashboard and the door. In some cars the fuses are mounted in the engine compartment, in front of the driver's side firewall. Check the fuses and replace if faulty.
2) 
Test the wiring harnesses from the fuse panel to the switches and from the switches to the window regulator motor. If the circuits test fine, then proceed to the next step. If a wiring harness is shorted or damaged, it will need to be replaced.3) Remove and test the switches on the driver's side door panel. Pry them up with a screwdriver and pull them free of the panel's opening. Disconnect the switch assembly from the wiring harness by pulling the adapter plug from the assembly. Test the switches individually by touching both sides of one switch with the circuit tester. Each switch will have two terminals, and if the tester is positive on both terminals while the window is activated, then the switch is good. Replace the switch assembly if any of the switches fails the test. Most power window switches come in assembled modules and cannot be replaced individually.4) Remove and test (if possible) the power window motor. Turn the armrest bolts and interior door handle screws counterclockwise, then pull the door panel free from the pop rivets. Behind the panel are a window regulator, the window glass, and the electric driver motor. The motor is usually located in the lower right section of the door. Unplug the motor from the wiring harness and unbolt it from the window regulator by turning the bolts counterclockwise. Pull the motor straight out, away from the gears. And check out if motor is receiving exact 12 volts at the terminals. If not then either motor is faulty or there is a confirm short if motor is replaced.
5) If all the above mentioned possibilities are checked out ok then the window regulator needs to be checked. Inspect the window regulator's joints for rust or stiff movement, if the electrical system is operating correctly. These joints can corrode or break, causing the window to stop working. With the door panel off, the window regulator can be removed and replaced by sliding the glass away from the track mounts, then turning all mount bolts counterclockwise and manipulating the regulator out of the door.
 
Thanks. keep updated for any more query.you can rate this solution and show your appreciation.

Jul 10, 2010 | 1995 Toyota Camry

2 Answers

How to find fuse for a 2006 chevy equinox driver's power window


power windows are not usually fused. They have a circuit breaker that controls all the windows. So if only one window is not working it is something like a bad switch or window motor. Remove the door panel and unplug the connector to the window motor and check for power and ground when activating the switch.

Jan 02, 2010 | 2007 Chevrolet Equinox LS New Cars

4 Answers

2004 saturn ion driver power windows switch will not work. Fuse good and passenger window switch works. The switch unit is good had a new on put on still did now work. Problems seems to be in wiring after...


Pull the rubber boot for the wiring harness in the door hinge area. I would suspect cut wires. Have the same issue. Bad design. What else is new.

Jun 12, 2009 | 2004 Saturn ION

17 Answers

Power windows, door locks and mirrors inop.


Sounds familiar - I pulled the rubber boot back and found the black wire was broken. I stripped the wires and put on a couple bullet connectors (terminators) and all is good. Just wish I would have seen this post before I took the door panel off... Oh well...

May 21, 2008 | 2004 Jeep Grand Cherokee

Not finding what you are looking for?
1997 Jeep Grand Cherokee Logo

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...