Question about 1984 Chevrolet S-10

1 Answer

1984 chevy S10 windshild wipers

How do i get my windshild wiper arm off of my 1984 chevy S10?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

At the arm remove the cap on end and their is a nut remove it 10 mm / Please rate my response thank you very much

Posted on Jan 29, 2009

1 Suggested Answer

MrScary66613
  • 1990 Answers

SOURCE: 1984 S10 wiper arms

No Problem! Look down on the Bottom of the Wiper Arm, wher it attaches and Swivels. There is a Small tab that comes off of the Upper Part of the Arm that looks like Two Front Teeth Sticking up just a Little. Take a Pair of Pliers and Pull this Tab Up Towards the Top of the Winshield to Release the Lock on the Arm. then take a Pair of Pliers with Tape on them so that you will not Scratch the Arm and Pull while you Wiggle the Arm right at the Swivel Pont and they will Come off. Please Rate my Response, I need all the Help That I can Get! Thanks!

Posted on Jan 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change wiper blades 2001 Chevy blazer


Open the cap at the end of the windshield wiper arm at the cowl of the Blazer. This will reveal the bolt that secures the wiper arm to the wiper linkage.
Unbolt the wiper arm using a 3/8-inch ratchet and socket. Place the bolt to the side, as you will reuse it later.
Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of workunderlined.png?1 to break it free, but with the right amount of wiggling, it will disengage.

Read more: How to Remove Chevy Blazer Windshield Wipers ' eHow.com http://www.ehow.com/how_6177302_remove-chevy-blazer-windshield-wipers.html#ixzz1B4pQJ39h
  • 3 Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of workunderlined.png?1 to break it free, but with the right amount of wiggling, it will disengage.

  • Read more: How to Remove Chevy Blazer Windshield Wipers ' eHow.com http://www.ehow.com/how_6177302_remove-chevy-blazer-windshield-wipers.html#ixzz1B4pJlPaV
  • 2 Unbolt the wiper arm using a 3/8-inch ratchet and socket. Place the bolt to the side, as you will reuse it later.
  • 3 Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of workunderlined.png?1 to break it free, but with the right amount of wiggling, it will disengage.

  • Read more: How to Remove Chevy Blazer Windshield Wipers ' eHow.com http://www.ehow.com/how_6177302_remove-chevy-blazer-windshield-wipers.html#ixzz1B4p1UYyB

  • 2 Unbolt the wiper arm using a 3/8-inch ratchet and socket. Place the bolt to the side, as you will reuse it later.
  • 3 Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of workunderlined.png?1 to break it free, but with the right amount of wiggling, it will disengage.

  • Read more: How to Remove Chevy Blazer Windshield Wipers ' eHow.com http://www.ehow.com/how_6177302_remove-chevy-blazer-windshield-wipers.html#ixzz1B4p1UYyB

    Jan 15, 2011 | 2001 Chevrolet Blazer

    1 Answer

    I have a 92 chevy S10 truck, how do you remove the wiper blades and arms?


    GM S10/S15/Sonoma Pick-Ups 1982-1993 Repair Manual Blade and Arm - REMOVAL & INSTALLATION
    (see Figures 1, 2 and 3)
    1. Matchmark the base of the wiper arm to the linkage. This will assure the arm is installed in the proper position. If the arm is being replaced, transfer the matchmark from the old component to the new one before installation. This can be done by placing the new arm on top of the old one and copying the mark.
    1bb2352.jpg

    Fig. 1: Removing the wiper arm using J-8966

    0234572.jpg

    Fig. 2: If no wiper arm tool is available, use a small prytool to depress the spring

    5227e24.jpg

    Fig. 3: With the spring released, pull the wiper arm from the linkage
    1. Most wiper arms are retained by a spring clip. Some are equipped with a release tab at the center which should be depressed to release the arm. If no tab is provided, use a small prybar or a wiper arm removal tool such as J-8966 to depress the spring and release the arm. Remove the arm from the vehicle.
    2. Some late model vehicles (all 1993 and some earlier models) are equipped with a wiper arm that utilizes a small release hole at the base of the wiper arm. If equipped, insert a 1 / 8 in. drift pin into the tool access hole to release the locking device and allow the arm to be easily pulled from the transmission. If necessary, use a gentle rocking motion to remove the arm.
    To install:
    1. Except for late model vehicles equipped with the tool access hole, align the matchmarks and gently press the blade over the linkage and snap into position.
    2. For 1993 vehicles (and earlier models equipped with the access hole on the arm) straighten the arm assembly and insert the pin. Align the arm with the linkage mark made earlier, then press down on the arm's head casting until it seats and locks onto the wiper pin. Remove the drift pin.
    3. Operate the wipers and verify proper alignment.

    Hope helps (remember rated this).

    Jul 08, 2010 | 1992 Chevrolet S-10

    1 Answer

    When I turn on the windshield wipers they travel too far hitting the windshild pillar(top) and the the cowl(bottom).


    The wipers are not installed correctly. Remove and reposition the wiper arms ,so they do not hit the side of the outside window pillar,when set to high speed.

    Apr 28, 2010 | 2003 Honda CR-V

    1 Answer

    How do you remove the windshield wiper arms


    The wiper arms have a push in tab at the very bottom at the fitting that is pressed into the wiper linkage below the screen. Use a flat headed screwdriver to pry out the tab. Once out the arm can be pulled right off. Now you can remove the cowling screen

    Apr 07, 2010 | 1987 Chevrolet S-10 Pickup

    2 Answers

    As I was driving my 92 Dodge Dakota with the wipers on, I heard a sound and they stopped moving. I can hear the motor running. Do you have a suggestion for this and what parts might be needed to fix it?


    had the same problem with mine all you need is a windshild wiper bushing it bout 5 to 10 $ at auto zone there are about 2 or 3 bushing that may need replacing mine was simplest one the one on the motor its easy it justs snaps onthe motor arm and than to the arms of the windshild transmistion

    Oct 15, 2009 | 1992 Dodge Dakota

    1 Answer

    Windshield wipers


    You might have a stripped wiper arm spline. Check it by seeing if it moves with your hand. Also check wiper arm connection under the black plastic unscrew and remove black plastic.

    May 06, 2009 | 2000 Mazda MPV

    1 Answer

    1984 S10 wiper arms


    No Problem! Look down on the Bottom of the Wiper Arm, wher it attaches and Swivels. There is a Small tab that comes off of the Upper Part of the Arm that looks like Two Front Teeth Sticking up just a Little. Take a Pair of Pliers and Pull this Tab Up Towards the Top of the Winshield to Release the Lock on the Arm. then take a Pair of Pliers with Tape on them so that you will not Scratch the Arm and Pull while you Wiggle the Arm right at the Swivel Pont and they will Come off. Please Rate my Response, I need all the Help That I can Get! Thanks!

    Jan 28, 2009 | 1984 Chevrolet S-10

    1 Answer

    Windshild wipers stuck on 96 ford explorer


    go to bottom of arm take end cap off loosen bolt / Turn on wipers Check to here the motor if its running if its running turn off and tighten up the bolt wiper arm at bottom then turn the wipers on if you here the motor running if you do not check fuse under dash and in engine compartment / Please rate my response thank you very much

    Jan 28, 2009 | 1991 Buick Park Avenue

    1 Answer

    1984 s10 winsheld wipers


    This is a very common Problem with Chevy Trucks. On my 95' Silverado, I had to Replace 5 Wiper Motors before She found one that she Liked. Even the Newer Trucks are Having the Same Problem with the Motors. Just Replace the Old one and get the Warranty with the New one. Please Rate my Response, I need all the Help That I can Get! Thanks!

    Jan 27, 2009 | 1984 Chevrolet S-10

    2 Answers

    My 2001 Buick Regal driver side wind shield wiper arm is stripped, it wipes at random. Please help


    i don't know what you mean by stripped, but iam gessing you mean it won't stay on the windshild when it wipes. have you tride another blade? if not i would try that first. if that dosent work you may have to try another wiper arm. all wipers will do what yours is doing when conditions are just right. you can minamise this problem maybe with a double wiper blade. hope this will help. OLD SCHOOL.

    Jan 10, 2009 | 1996 Buick Regal Olympic Gold

    Not finding what you are looking for?
    Cars & Trucks Logo

    368 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    61292 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...