Question about 1995 Toyota Camry
Quiero ver como se sincronizan los arboles de levas
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Tengo un Toyota Yaris del
Hi. It must be really very frustrating on your end and i understand how you feel. I suggest that have your car checked by toyota mechanics since it is still under the warranty.
Posted on Oct 20, 2010
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.
CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence.
Posted on Dec 23, 2010
SOURCE: como poner el sensor de
PROBABLEMENTE ESTE DEBAJO DE LO QUE SE LE LLAMA LA ARANA (EL MANINFOLL) MUCHOS CARROS LOS TIENEN AHI PARA ESO TINES QUE DESARMAR TODO LO QUE ESTA POR ENCIMA DEL MOTOR PERO PRIMER CHEQUEA ALREDEDOR DEL MOTOR ES UN CABLE ELECTRONICO Y EL SENSOR SE PARECE AL SENSOR DE GASES
Posted on May 24, 2011
tienes que poner el cylindro numero 1 a TDC. en el cyclo de compresion del cylindro. pon el dedo en el abujero de la bujia y que le de vuelta alguien al motor, y cuando sientas que sale aire, entonces estas en el cyclo de compresion, despues ponle un desarmador largo al cylyndro y cuando le des vuelta al motor fijate que llegue el desarmador a la posicion mas alta antes de que se vuelva a bajar y entonces estas en TDC. Ya cuando estas en TDC, ponle la cadena de tiempo al carro y listo.
Posted on Jun 27, 2011
Tips for a great answer:
Oct 26, 2013 | 1995 Toyota Camry
May 24, 2011 | 1989 Toyota Camry
Sep 06, 2010 | Toyota Corolla Cars & Trucks
Jan 17, 2010 | 1989 Dodge Caravan Cargo
Oct 16, 2009 | 1994 Volkswagen Jetta
Apr 30, 2009 | 2003 Ford Ranger Regular Cab
Sep 14, 2008 | 2006 Ford Explorer
Jun 17, 2008 | 1999 Daewoo Leganza
338 people viewed this question
Usually answered in minutes!