Question about Cars & Trucks

Open Question

2004 ford f550 powersteering pump removal and replacement

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 261 Answers

SOURCE: Problems removing power steering pump to replace water pump

i use a 1/4" drive 10mm long socket and insert it through the openings on the pulley and turn the pulley to acess all the three or four bolts and the pump should be out but removal of the p/s belt will make it even easier!!

Posted on Nov 24, 2008

Ad
ewashmidas
  • 362 Answers

SOURCE: powersteering pump

P/S PUMP, R&R All Models 2.4L 1996 - 2000 1.7 hours 3.0L 1996 - 2000 1.7 hours 3.3L, 3.8L 1996 - 2006 2.5 hours
This is the time for a expereniced tech, with the right tools, working with no breaks and no rusty or broken bolts. Hope this helps.

Posted on Jan 25, 2009

  • 109 Answers

SOURCE: how do i remove the Powersteering pump in my 1998

Replace the ps pump, brake fluid is not a lubricant, your pump is scored, raise the van, block it, remove the sheild, belt and right axle, and remove the pump, you will have to flush the system with 4-5 litres of PS fliud only. GOOD LUCK, RDJRP

Posted on Oct 03, 2009

Testimonial: "thanks for the feedback, I figured the pump is gone , so it is not worth the efforts to seal eery detail"

  • 1 Answer

SOURCE: 2001 Ram 3500 Truck: replacing powersteering pump on 1999 dodge 1 ton 3...

it is best to remove the pwr st. pump and vaccum pump assy as a unit which is held to the front cover w/2 15mm head bolt and a support bracket on the bottom bolt next to the block @ the pwr st pump. and disconnect all lines. get the seal kit and replace them @ this time. if you don't and just replace the pump you will probably develop an oil leak where the shaft meshes w/ the adapter. 

Posted on Oct 21, 2010

  • 157 Answers

SOURCE: how do you remove the rear rotors on a 2004 f550

heres a web site that might help http://www.ehow.com/how_4507986_replace-rear-disc-brakes-ford.html hope it helps

Posted on Nov 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's your question?how do i bleed powerstering pump for 2004 ford bantam


easy fill resevoir then turn steering full lock left to right about twice ,check fluid level ...job done

Oct 06, 2015 | Ford Cars & Trucks

1 Answer

My 99 ford contour's steering is VERY stiff while driving, and I had put powersteering fluid in it earlier this morning. what's going on?


may be you have a leak and your car run out of powersteering fluid or your powersteering pump os no good.

Aug 31, 2012 | 1999 Ford Contour

1 Answer

I have a 2003 ford f550 it has a bad vibrathon at 40 to 50 and it gets relly bad at 65 70 every thaing is good on the front end what could it be.


i have f150 same thing happened but it was bearing hub when i jacked truck up there was only like 1/4 inch of play which i didnt think was baduntil i removed hub it was shot

Jul 03, 2012 | 2004 Ford Super Duty F 550

1 Answer

Brake lights not working on 2004 ford f550 . cannot seem to find fuse list for truck.


try using 12v light conect to ground touch each side of fuse if light comes on fuse is good,you can also check brake switch at pedal.

Aug 21, 2011 | 2004 Ford Super Duty F 550

1 Answer

To change the serpentine belt on a 2004 explorer will the timing be affected? ...


No, not at all. The timming belt, or may be a chain on that vehichle? Not sure. But it is under a cover on the front of motor and you have to take everything off of front to even get to it.

The serpentine belt just runs the a/c, alternator, water pump, and powersteering pump.

Dec 17, 2010 | 2004 Ford Explorer

1 Answer

How do you remove power steering pump on 1990 ford tempo gl


  1. remove the powersteering belt.
  2. Use a puller to remove the pulley.
  3. remove the powersteering lines, theres a preasure line and a return hose
  4. remove the three bolts holding the pump to the bracket,
  5. reverse directions to install new pump. hope this helps.

Oct 24, 2010 | 1990 Ford Tempo

1 Answer

How do i remove the Powersteering pump in my 1998


Replace the ps pump, brake fluid is not a lubricant, your pump is scored, raise the van, block it, remove the sheild, belt and right axle, and remove the pump, you will have to flush the system with 4-5 litres of PS fliud only. GOOD LUCK, RDJRP

Oct 02, 2009 | 1998 Dodge Grand Caravan

1 Answer

What type of oil do I need for my Ford F550 V10 Gasoline Stake?


You need 5W20 for the non-turbo 6.8L EFI.
Please remember to rate this fix.

Feb 13, 2009 | 2004 Ford Super Duty F 550

1 Answer

Loss of PS fluid, Slipping Transmission, Loss of Tranie fluid


the whine is from the power steering pump...you probably have a split line that needs replaced..

Jan 04, 2009 | 1995 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...