Question about Cars & Trucks

Open Question

2003 ford escape v6 3.0 overdrive problems car misfire

Overdrive problem win car is in overdrive

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 34 Answers

SOURCE: 2005 Ford Escape XLT 4WD - Overdrive light blinking...

The overdrive light blinking means that a fault code has been stored in the computer, this can be for many different reasons. The car isn't actually turning overdrive on and off, it is just a way to alert you of a problem. Getting the computer scanned will provide a fault code eg. P(XXXX) if you can get this code I can help you further. -Jared

Posted on Nov 14, 2008

  • 94 Answers

SOURCE: 2002 ford escape v6 misfire after washing engine

coil packs got wet take wires off and put dialectic grease in the boot ends

Posted on Mar 08, 2009

  • 811 Answers

SOURCE: p0316 and misfire codes coming up

take to local ford mechanic

Posted on Sep 12, 2009

  • 6 Answers

SOURCE: headlight went out in 2003 ford escape i have

you have to remove the whole headlight assembly, then pop off the front cover pull the old bulb out and put the new one in. reverse the process to re-install. there is a small plastic tab on the topfront of the headlight assembly, that is what you need to release to get the clear cover off and get inside.

Posted on Oct 07, 2009

  • 312 Answers

SOURCE: Ford Escape 2003. Engine suddenly overheat.

Engine over heating can be caused by a number of things. When you say the water pump and radiator appear to be ok I am also guessing that you checked the coolant level to make sure it is normal.

If the level is low then you obviously have a leak. Insufficient coolant circulating will not cool the motor properly because it won't be able to draw enough heat out. If the level is normal then you need to check the thermostat to make sure it is opening properly. To do this, run the motor to temperature and check the top and bottom hoses. They should both be hot and firrm once the thermostat opens meaning the circulation loop is operating properly. If the top is hot and firm and the bottom is cold/soft or collapsed then the thermostat isn't opening.

If the thermostat is operating properly then you ned to look for some other obstruction or cause for coolant loss. Check the head/intake gaskets, hose connections, hoses, over flow tank, radiator fins, radiator side tanks etc..

Good luck.

Posted on Jun 10, 2010

Testimonial: "Thank you for your quick response. I will get the head/intake gasket checked."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 ford escape 3.0L code PO353


I would think that many misfire codes would mean it runs terrible,coils go bad alot on the early ones,if it runs badly ,coils are suspect.
would say crank sensor if stiil runs ok,but the cam noise is not good,
lean or misfire won't make the cam noisy,something is broken in the valvetrain

Jan 03, 2014 | 2003 Ford Escape

1 Answer

I have 2003 Ford Escape V6 I have to codes that read p0141 and p0161 and the car misfires I need help with this problem


P0141=O2 Sensor Heater Circuit Bank 1 Sensor 2
P0161=O2 Sensor Heater Circuit Bank 2 Sensor 2,
the 141 code is a problem with the heated O2 sensor on the drivers side exhaust after the converter,
the 161 code is the same except it is on that passenger side exhaust after the converter.

Jan 23, 2010 | 2003 Ford Escape

1 Answer

2003 ford escape. 75,000 miles on it. Sputters


What engine do you have?
I have a 2002 Escape with 3.0 V6. It sounds like the ignition is getting damp and the engine is misfiring. If the CEL is flashing, you really shouldn't be driving it. Check the owners manual, but you could damage the engine.
Anyway, go to an Autozone or other parts store. Many will scan your engine for the DTC code for free. This code will give you a clue.
My code was for a for a cylinder misfire. I was close to 100,000 miles, so I replaced the plugs first, then the one coil. It was the coil.

Oct 18, 2009 | 2003 Ford Escape

1 Answer

P0316 and misfire codes coming up


take to local ford mechanic

Sep 12, 2009 | 2003 Ford Escape

1 Answer

I encounter misfiring in engine of ford escape 2003


unless your vehicle is equipped to handle the bio fuel it will act funny, try running it without and see what happens.

Jul 30, 2009 | 2003 Ford Escape

2 Answers

Abs light troubles


Possibly have a bad speed sensor or something else. You will need to have it hooked to a computer to find out what is going on with it.

Jun 14, 2009 | 2003 Ford Escape

1 Answer

Cylinder 1 misfire '02 Ford Escape


CHECK COIL TO NUMBER 1 CYLINDER.AND FUEL INJECTOR TO NUMBER 1 CYLINDER.IF ALL IS GOOD YOU HAVE INTAKE LEAK OR MECHANICAL PROBLEMS TO THAT CYLINDER.

Jun 12, 2009 | 2003 Ford Escape

1 Answer

Misfiring escape 2003


Check timing/ timing belt. May have jumped one cog.Remove and replace.

Jun 07, 2009 | 2003 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...