Question about 2000 Chevrolet Silverado

Open Question

What is the size of metal brake lines for a 2000 chevy silverado

Posted by Anonymous on

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 508 Answers

SOURCE: Star bit on front brake 2000 chevy 1500 ?


Posted on Jan 24, 2009

Auto Master
  • 139 Answers

SOURCE: 00 Chevy Silverado... ABS EBCM diagram help??? Brake line hookups

I hope this helps.

Thank You,

Posted on Aug 28, 2009

  • 468 Answers

SOURCE: Power steering and brake line location2002 Chevy Silverado 2500HD

the power steering lines are very short hoses approximately 8 inches long that go from the power steering pump down to the steering box, which is located on the frame, just below the pump. The brake lines run from the master cylinder(where you fill it with fluid on the drivers side firewall) down to the frame, and then follow the frame both directions; both to the front end and the rear end, along the drivers side frame rail, just on the inside of it. The fuel line runs along the same path to the rear.

Posted on Oct 03, 2009

  • 631 Answers

SOURCE: what tools do i need to change the rear brake pads

If you have disc brakes then all you need is a c-clamp to compress the brake caliper. If you have drum brakes then you really need to purchase a pair of brake pliers and pair of small vise grip pliers or tool to re-install your retainer springs. It isn't very expensive for either and not hard to change your own brakes. Just do one at a time and don't take everything off of both sides in case you have to look at the other side to see how things go back together. You will have to jack up one side at a time to take the tire off.

Posted on Nov 24, 2009

  • 75822 Answers

SOURCE: can't get brake fluid from abs into lines after

I read this same problem all the time, the reason u can't bleed the lines is that a special tool is required that pluge into the ABS and holds the hydraulic valves in the ABS control open for bleeding, there is no way around this.

Posted on May 19, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


Brakes grab for several reasons. worn linings /pads that allow metal to metal contact with disc or drum,. oval drums , brake shoes incorrectly fitted, oil on linings or pads. excessive clearance between shoe and drum that allow the shoe to race to the drum and grab instead of a small movement to get contact. If drums adjust correctly

Jan 23, 2013 | 2000 Chevrolet Silverado 1500

1 Answer

How do i bleed the brake lines from my 2000 chevy silverado

You need a special tool to bleed the brakes due to the Anti Lock brake system. You will need to see the dealer on this or a well equipped brake repair shop.

Aug 08, 2012 | Chevrolet Silverado Cars & Trucks

1 Answer

I have a 2000 chevy silverado, the front left brakes keep getting stuck and i just change caliper for the second time so i know its not that.

It may be a bad rubber brake line that connects to that caliper, preventing brake fluid from exiting the caliper. Older rubber brake lines can collapse internally and prevent fluid passing through. If the rubber feels spongy, it needs replacing.

Jul 01, 2012 | 2000 Chevrolet Silverado 1500

1 Answer

Need to know what size allen wrench to take off front disc brakes on 2000 chevy silverado 4.8 l

The caliper guide pins will usually have either a 3/8 inch or a 5/16 inch allen head bolt. If the brake calipers are found to have phenolic pistons then it would be advisable to change them with calipers that have metal pistons.

Sep 21, 2010 | 2000 Chevrolet Silverado 1500

3 Answers

Can't get brake fluid from abs into lines after installing new brake line on a 2000 chevy silverado

I read this same problem all the time, the reason u can't bleed the lines is that a special tool is required that pluge into the ABS and holds the hydraulic valves in the ABS control open for bleeding, there is no way around this.

May 19, 2010 | 2000 Chevrolet Silverado 1500

1 Answer

2000 chevy silverado; not all the time but every so often when i step on the brake pedal it feels like it gets hung up on something and it wont depress.when i take my foot off for a second and step on it...

Check the brake pedal rod.Make sure it is not binding.Remove the rod and work the brake pedal and make sure it does not catch or stick to anything.Look at the pedal real closely and make sure there are no cracks in the metal where it pivots.Good luck.

Dec 07, 2009 | 2000 Chevrolet Silverado

1 Answer

How do you drain brake lines after new ones are put in on a 2000 chevy silverado

the easiest way is to open all the bleeders and let gravity do the work for you or you can do it one wheel at a time and bleed them induvidually

Aug 09, 2009 | 2000 Chevrolet Silverado

Not finding what you are looking for?
2000 Chevrolet Silverado Logo

Related Topics:

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides