Question about 2000 BMW 328i

1 Answer

Got a code p1421 on my 2000 bmw

I have a 2000 bmw 328i,I pulled a trouble code p1421.have do I fix it

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

Secondary air air system bank 2

may need a air pump bank 2 or a air diverter valve

hope that helps

Posted on Jan 31, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 840 Answers

SOURCE: 1998 BMW 328i Rear WIndows broken

then it is the actual buttons for the windows on the rear doors

Posted on Apr 12, 2009

  • 1 Answer

SOURCE: 328I BMW radio code-where/how do you find it

if you no longer have the coded card that came with the manual when new, you will have to bring your photo id and vehicle registration to any bmw dealer, they will supply it to you. provided you are the registrant.

Posted on Jul 17, 2009

  • 490 Answers

SOURCE: 2000 BMW 328i yellow oil light on but oil is fine

Your sensor is going bad or you have to change your oil.

Posted on Jul 29, 2009

ZJLimited
  • 17970 Answers

SOURCE: BMW 328i Starter how to replaice

1999 BMW 328I 2.8L EFI DOHC 6cyl

Starter - Removal & Installation

The starter motor on some models is very difficult to see from the top of engine compartment as it is covered by the intake manifold. On these models, without removing the intake manifold, the starter motor must be removed from underneath the vehicle. Because the starter motor mounting bolts are not easy to access, a long extension with a universal joint mounted on a proper sized socket could be used. A three foot transmission extension is commercially available from tool vendors that has a 3 / 8 inch drive of the driven end and 1 / 2 inch drive on the drive end. If used with a non-binding impact universal joint and a proper fitting impact socket, the starter motor fasteners can be removed from underneath the vehicle.
Once the starter motor fasteners are removed, the starter motor may have to be moved side-to-side several times to loosen the dowel pin if it has corroded in place.

NOTE When the battery is disconnected, the radio code, on-board computer and clock settings will be lost. The radio code should be obtained before disconnecting the battery or radio. Once the battery has been reconnected, the radio will not function unless the code is keyed in.
Starter motor electrical terminal fastener torque specifications for all models:
M5 terminal fasteners: 44 inch lbs. (5 Nm)
M6 terminal fasteners: 53 inch lbs. (6 Nm)
M8 terminal fasteners: 115 inch lbs. (13 Nm)
Starter motor mounting fasteners:
Hex head bolts: 36 ft. lbs. (49 Nm)
Torx bolts: 32 ft. lbs. (43 Nm) Starter motor electrical terminal fastener torque specifications for all models:
M5 terminal fasteners: 44 inch lbs. (5 Nm)
M6 terminal fasteners: 53 inch lbs. (6 Nm)
M8 terminal fasteners: 115 inch lbs. (13 Nm) Starter motor mounting fasteners:
Hex head bolts: 36 ft. lbs. (49 Nm)
Torx bolts: 32 ft. lbs. (43 Nm) E36 6-Cylinder Engines
Automatic Transmission Models

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Set the ignition switch to the OFF position.
  3. Disconnect the negative battery cable.
  4. Remove the climate control air intake duct at the rear of the engine compartment as follows:
    1. Release the grille clips at the rear and lift the grille upward from the rubber seal, then remove the seal.
    2. Remove the two self tapping Phillips screws from inside the duct to release the electrical harness housing.
    3. Press the electrical housing downward to expose and remove the two hex head self tapping screws on each side of the duct and lift the duct up and out of the engine compartment.
  5. Remove the intake manifold trim and valve cover trim covers.
  6. Disconnect the ignition coil electrical connectors and ground straps, label for reinstallation and place aside.
  7. Remove the two fasteners that secure the fuel injection electrical connector harness to the rail. Remove the harness and carefully place aside toward the back of the engine compartment behind the right side strut tower.
  8. Remove the intake manifold.
  9. Remove the electrical leads from the starter motor and place aside.
  10. Remove the starter motor mounting fasteners at the transmission bell housing, then remove the two mounting nuts at the L-shaped mounting bracket.
  11. Loosen the L-shaped bracket to engine block mounting bolt slightly, then remove the bolt while supporting the starter motor.
  12. Remove the bracket, then lift the starter motor upward away from the engine.
  13. Visually inspect the starter pinion and ring gears for any signs of damage.
  14. Installation is in reverse order of removal.
Manual Transmission Models
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Set the ignition switch to the OFF position.
  3. Disconnect the negative battery cable.
  4. Raise and safely support the vehicle.
  5. Remove the fasteners for the reinforcement mounted between the frame rails just behind the rear lower control arm bushing brackets. Mark the bar-s direction for proper reinstallation and remove the bar.
  6. Remove the fuel line cover located near the left side rear lower control arm bushing bracket.
  7. Release the fuel lines and reverse light wiring from their routing brackets.
  8. Note the routing of the starter motor electrical wires, remove the wire mounting nuts, and place the wires aside.
  9. Remove the top and bottom starter motor to engine-transmission mounting fasteners.
  10. Remove the two mounting nuts at the L-shaped mounting bracket.
  11. Loosen the L-shaped bracket to engine block mounting bolt slightly, then remove the bolt while supporting the starter motor.
  12. Remove the bracket and carefully lower the starter motor downward away from the engine.
  13. Visually inspect the starter pinion and ring gears for any signs of damage.
  14. Installation is in reverse order of removal.

Fig. A view of the starter motor mounting fasteners and dowel pin. The mounting bolts are threaded into the starter motor

cd45991.jpg

Fig. The starter motor mounting bolts are a different size than the transmission-to-engine mounting bolts

2cbfa11.jpg

I hope help you with this (rated this help) Good luck.

Posted on Sep 22, 2009

  • 1 Answer

SOURCE: 1997 bmw 328i conv.

radio does not work on my 1997 bmw 328 it gives the message
"phone" a mechanic pulled it out of its slot and reset the code...it worked for two days and again it doesnt work with same message

Posted on Sep 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Eml came on in my bmw 328i 1999 please how to fix this problem


First thing you need to do is to have the car scanned with a engine malfunction light scanner . then you'll get a engine trouble code.

depending on what is the code then search on google for bmw 328i 1999 engine trouble code list and repair procedures.


to find out what codes meens go to that link http://www.obd-codes.com/trouble_codes/bmw/.

Nov 09, 2015 | BMW Cars & Trucks

1 Answer

What is the radio unlock code for a 1996 BMW 328i?


If you cannot find the code written on something in the glove box, you will have to remove the radio. Once removed, you will need the serial number off of the radio chassis. You can call BMW with this number and they will give you the code.

Hope this helps!
-Scott

europartsplus.com

Aug 19, 2014 | 1996 BMW 328i

1 Answer

What is the unlock code for a 1996 BMW 328i radio


If you cannot find the code written on something in the glove box, you will have to remove the radio. Once removed, you will need the serial number off of the radio chassis. You can call BMW with this number and they will give you the code.

Hope this helps!
-Scott

europartsplus.com

Aug 19, 2014 | 1996 BMW 328i

1 Answer

2007 BMW 328i back driver window is not rolling up, help?


It's probably the window regulator, common problem in BMW.
It's not hard to replace, but if not mechanically inclined, better to take to a dealer or your independent BMW technician, the part is not terribly
expensive (for a BMW)but labor might run into some $$ at the dealer.

Mar 18, 2013 | 2006 BMW 3 Series

3 Answers

1997 bmw 328i conv.


If you're talking about the Anti-Theft Security code for your radio, I'm fairly sure that only a BMW Dealership would be able to retrieve and reset the radio.

You could also try disconnecting the battery terminals for 10-20 minutes, and see if it resets.

May 16, 2008 | 1997 BMW 328

Not finding what you are looking for?
2000 BMW 328i Logo

Related Topics:

314 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...