Question about 1995 Dodge Dakota

1 Answer

I put a new clutch in it and every thang went good but went to ingag the clutch and it wont go in to gear in lees the truck is not streted when u put the truck in gear then step on the cluch it trys to go even with the cluch pushed but if u have the truck started it wont go in to gear i thaink it has somthing to do with the slave cil like it needs bleed

Posted by on

  • tjistheshit Jan 28, 2009

    thanks do u no how to bleed it

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 114 Answers

HI there... You might be right. If you can't put the truck into gear then you might have air in the slave. Try beeding it and see if that helps.

Posted on Jan 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Put in a new clutch in my ford escort zx2 it goes in gear when car isn't running won't when car is


air might be in the clutch need to bleed it and see if that does it
these newer cars have a clutch master cylinder and slave cylinder, when ya mash it flid moves the slave to depress clutch fork and release pressure plate from flywheel. if its ait in the thang it wont release check brake fluid level in clutch master fill it up with recommended brake fluid for your clutch

Jan 06, 2017 | Ford Cars & Trucks

2 Answers

My clutch going to the floor and not being able to put it in gear my master cylinder was empty i refilled that and pumped the clutch an it is still doin same thang what else could be the problem?


Hi Sarah:
Chances are that you still have the clutch problem that you started with.
Filling the master cylinder was good, now you have to find out why it was empty and where it went.
You'll need to make sure there is no air trapped in the lines so you'll have to bleed the slave cylinder.
If the slave cylinder seal has failed, it will have a lot of fluid visible so its fairly obvious.
Remove and replace, bleed lines, check fluid level, should be OK.

May 04, 2015 | 1995 Nissan Maxima

1 Answer

94 ford ranger manual transmission goes into first gear and reverse just fine let off the clutch and the truck wont move.


part of a clutch job is removing the gearlever make sure the lever is secured properly and selects the gear correctly.
Orherwise your symptoms sound like a collapsed pressure plate or broken release bearing either defective part or something done wrong during installation of clutch

Apr 13, 2017 | Cars & Trucks

1 Answer

Air conditionor was noisey then turn on engine would stop ,now it will not do anything even if set on max air cond. where is fuse?


It is possible you are low on freon, if so the clutch will not ingage, It is also possible that the Clutch on the compresser went out., If this happens it would break the belt because the clutch wont turn....good luck

Mar 12, 2011 | 2003 Nissan Altima

1 Answer

Put car in reverse after car warms and it doesnt ingage until you push on the gas. It stays in the nuetral position


hi sound like the clutch is worn and your having to use the speed of the engine to help you ingage the gear.Does the clutch slip at all when driving in a forward gear ?

Sep 02, 2010 | 1993 Saturn SC2

1 Answer

How do i know if my whole clutch is out on my rodeo 99?... the pedal is easy to ingage half way down and im not able to switch gears


At a standstill put the car in 3rd gear and try to get the car to move. If it stalls you clutch is fine. If you able to move the vehicle w/o stalling you need a new clutch.

Apr 09, 2010 | 1999 Isuzu Rodeo

1 Answer

Cant shift unless i compression shift


Chances are pretty good your clutch is toast ! If your truck has a hydraulic clutch , in which mine doesn't , get a friend to pull the boot off of the clutch fork , and with a light , make sure it is disengaging the clutch at all . If you have a mechanical clutch , simply adjust it out til the problem goes away . Look forward to a new clutch very soon ! good luck !!

Apr 20, 2009 | 1992 Chevrolet C2500

1 Answer

Clutch ingages all the way in new clutch


Well I can tell you this that the clutch has to much free play, I would check the slave cylinder for proper operation, but if it is defective the slave and mater are better replaced as a pair.

Dec 02, 2008 | 1988 Chevrolet K1500

2 Answers

Stuck in 5th gear


try bleeding your clutch

Aug 19, 2008 | 1991 Ford Ranger Supercab

Not finding what you are looking for?
1995 Dodge Dakota Logo

Related Topics:

241 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

71162 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6992 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...