Question about 1998 Chevrolet Cavalier

1 Answer

Programming alarm on chevy cavalier

I have a new remote for my 2002 chevy cavalier. need to know how to program it.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 39 Answers

The easiest way to do this is to take your ca to the chevy dealership and have them program it for you most places will do this for free, so you should call around to see if they charge.

Posted on Jan 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to program new remotes for a 2009 chevy hhr


As far as I know you need a special tool (Tech II) from Chevrolet to program the remotes. Don't think you can do it on your own. You can double check your owner's manual but unfortunately I think you have to go to the dealer.

Nov 07, 2013 | 2009 Chevrolet Chevrolet HHR SS

1 Answer

Can a new remote be programmed if alarm is set?


Hi Kim, When you ordered the new key the dealer should have asked for the chassis number? That gives them the codes to pre program. so that it should activate and deactivate the alarm, if that is the problem! ? Regards John

Jul 02, 2012 | 2000 Pontiac Grand Prix

1 Answer

Key fob


Walk out to the vehicle with a new battery in the key fob and press the lock AND unlock button at the same time while you stand close to the vehicle for 7 seconds. You will hear the doors go thru a lock and unlock cycle, your fob is now programmed. This will sync existing programmed controllers, security sync. to program new remotes:In the trunk, connected to the wireless remote controller (driver side on wheel well, need to remove 'mat') is an empty connector with 2 wires connected. short the two connector pins. The locks will all cycle. Press and hold lock/unlock buttons on remote until locks cycle on/off. repeat for other remotes. Remove short across connector pins. Test new remote(s).Warning:existing remotes are deprogrammed, only remotes programmed will work from now on.This worked on my 1998 Cavalier. Be sure battries in new remote(s) are good! Answer Locate the data link connector under the dash (under the steering column). Ground out pin #8 of the DLC (top right port) with a jumper wire to any piece of metal close by (I use the e brake hardware). The door locks will then lock & unlock to let you know you are in the programming mode. Simultaneously press & hold the lock & unlock button on one of the keyless entries until the locks cycle (this lets you know the transmitter has been programmed). Repeat this step for your second transmitter. You must reprogram the 2nd transmitter within 60 seconds of programming the 1st one or you have to start over.
Note

Read more: http://wiki.answers.com/Q/How_do_you_program_a_keyless_remote_for_a_1996_Chevy_Tahoe_LT#ixzz1wjwEcG4s

Jun 03, 2012 | Oldsmobile Cutlass Supreme Cars & Trucks

1 Answer

Remote start program for autopage xt60 alarm


how to programe the remote to my 2003 chevy malibu

Apr 02, 2012 | 2002 Honda Civic

2 Answers

I have a 2006 Chevy HHR, bought used about two years ago. We already replaced the keyless remote one (at $90) and it won't work again. New batteries didn't help. When you use the key on the door (rather...


You are going to need to recalibrate the remote to the vehicle. As long as the remote works correctly which i think it should. It will actually tell you how in the owners manual. I am not current with the HHR as i have not worked on one yet. They must be reliable!

May 03, 2010 | 2006 Chevrolet HHR

1 Answer

Program a new fob to my 2002 f150 supercrew lariat 5.4L remote lock/start system


if it is a ford remote or ford factory alarm remote cycle the key from off to run(usually 8 times) untill you hear door locks activate. at this exact time key needs to be in the on position.touch unlock or lock on all remotes being programmed and make sure door locks respond to remotes. then turn key off ending programming mode.then try your fobs they should work

Nov 06, 2009 | 2002 Ford F150 Regular Cab

2 Answers

Got an used Hyundai Sonata 2002, need to program the remote for keyless entry. Please help.


hi you can look up what we call the chicken dance on the internet for hyundi it is sequence of moves to program new keys and remotes if you cant find hyundi will program for you.

hope this helps

Jun 17, 2009 | Hyundai Motor 2002 Sonata

1 Answer

Reprogram keyless entry


It took me a few attempts to program a new keyless remote for my 2002 Chevy Blazer.
Insert key into ignition but don' turn it yet. While holding down the UNLOCK switch on the door, the trick is to cycle the ignition ON OFF ON OFF as quickly as possible then release the UNLOCK switch. If done correctly the door locks will cycle 1x to acknowledge. Then hold both the unlock and lock buttons down on the remote for about 15 seconds. The locks should cycle again to confirm...Hope this helps.

Mar 19, 2009 | 2002 Chevrolet Blazer

1 Answer

PROGRAMING ALARM REMOTE ON 95 TAHOE


Here it is straight from Alldata:
  1. Ground pin G of the Data Link Connector (DLC).**Bottom left pin**
    • Receiver will respond by locking, and unlocking doors within 2 seconds.
  1. Press any button of the first transmitter to be programmed.
  2. The control module will respond by locking/unlocking doors and activating rear window release.
  3. Press any button of the second transmitter to be programmed (if used).
  4. The control module will respond by locking/unlocking doors and activating the rear window release.
    1. Remove the ground applied to the reprogrammed connector.
      1. Transmitter operation is verified locking and unlocking the doors and activating the rear window release

Dec 23, 2008 | 2007 Chevrolet Malibu SS Sedan New Cars

2 Answers

How do you program a new keyless enrty remote for a 2004 chevy cavalier ls sport


How can I Program my Keyless remote for my 2004 Chevrolet Cavalier?My E-Mail address is Johnhegedus@ptd.net

Oct 16, 2008 | 2004 Chevrolet Cavalier

Not finding what you are looking for?
1998 Chevrolet Cavalier Logo

Related Topics:

300 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...