Question about Cars & Trucks

1 Answer

Replacing thermostat on 03 trail blazer

There are two screws holding thermostat and the bottom screw is in a tight spot would a swivel reach this screw or do i have to remove power steering pump

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

You will need to use a 1/4 inch drive with a swivel head socket to get it out good luck.

Posted on Jan 24, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 TRAIL BLAZER BLOW AIR OUT BOTTOM & DEFROST ONLY


vacuum leak somewhere. did someone put in a aftermarket radio? most times they will screw something up when they do replace factory items.

Apr 20, 2014 | 2002 Chevrolet Blazer

1 Answer

Replace transfer case vaccum switch


reach it and remove the switch with a wrench, you should not lose any fluid.it just screws out, It shoulnt be in there too tight. make sure not to mix up vacuum hoses. good-day!

Apr 11, 2014 | 1998 Chevrolet Blazer

1 Answer

I need to replace power window switch on drivers side. 2004 chevrolet trail blazer. how do i remove door panel?


remove screws from door handle and with a flat screw driver go around the edge of panel and pop out the panel be very careful when doing this ,and to replace just tap hard enough on the plastic clips

Feb 08, 2011 | 2004 Chevrolet TrailBlazer

1 Answer

How change the thermostat to a chevrolet trail blazer


Remove the alternator and the bracket. Easier to take off if the drivers front tire is off. Have fun with the 3rd bottom bolt on the alternator, it's a blast trying to get it off.

While you're removing the thermostat, you might as well replace the coolant temperature sensor like 2" above the T-stat. It's around $35 and very easy to do. The sensor screws into the block and has a wire coming off of it that will need to be unpluged to remove.

Jan 16, 2011 | 2003 Chevrolet TrailBlazer

1 Answer

Just want to replace tail light on a 2003 Trail Blazer, and as I see it there 2-screws you need to unfasten before the plastic hub comes off. Is that correct.


That would be correct, then unscrew the bulb unit from the back side, I believe it's 4 small screws on the back. Pull your bulbs out and replace.

Oct 30, 2010 | 2003 Chevrolet TrailBlazer

2 Answers

2002 Trail Blazer. Wipers work on low and high


sounds like the wiper module is bad. if it is toy will have to replace the wiper motor. the module is built right in

Feb 05, 2010 | 1999 Chevrolet Suburban

1 Answer

Trail blazer gas gauge reading empty when its


The sending unit in the gas tank must be replaced it may be possible to gain access through the back storage compartment by lifting up the rug look for an access panel with a couple of screws holding the plate on remove it and you should be able to look down through and see the gas tank and a couple wires going to the sendind unit unscrew the screw remove and replace if access plate is not there then it is possible the gas tank must be removed to do the job purchase a Haynes repair manual.

Nov 06, 2009 | 2002 Isuzu Axiom

2 Answers

Changing headlight on ford focus 2003


It is very hard to get to but you need to turn the bulb housing counter clock wise and it should pull out far enough to replace the bulb. Be sure not to touch the new bulb glass with your hands. grab it by it's housing. then reverse the process.

Mar 03, 2009 | 2000 Ford Focus

1 Answer

How do I replace the thermostat in a 95 chevy Beretta 3.1 v6


you need a socket and a swivel to reach it, the bottom hole in housing is slotted so you won't need to take the bolt all the way out.

Feb 12, 2009 | 1995 Chevrolet Beretta

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...