Question about Cars & Trucks

Open Question

Crankshaft location sensor on mitsubishi colt d-id 2006

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
DSMprostyle
  • 37 Answers

SOURCE: crankshaft position sensor location

Hello. One way to check if it is working is when you try to start the car does the needle move on you tac? If not then your crank sensor is more then likely the problem. It is located on the backside of the engine under the intake manifold. If is in about the center of the block. There will be a 10mm bolt holding the sensor in. If you decide to change it yourself (not to terrible of a job) unplug the sensor, remove the bolt and spin it back and forth slightly while pulling it out. It may be stoburn and you might have to work at it for a little bit (not a done of room) but it will come. When it's out the sensor will be shaped kind of like an L. I have changed a few of these over time and they can be a little stoburn. To install just reverse the process.

Posted on Mar 26, 2009

Ad
polarcycle
  • 1392 Answers

SOURCE: 2004 DODGE STRATUS 2.7L, Location of Crankshaft Position Sensor?

it is located on the right side of the motor, in the trans area. Actually in the bell housing.

Posted on Jun 23, 2009

  • 880 Answers

SOURCE: where is the crankshaft sensor located ?

The crankshaft position sensor (POS) is located on the oil pan facing the gear teeth (cogs) of the signal plate. It detects the fluctuation of the engine revolution.
After replacement, ECM reprogramming is required.
This vehicle may be subject to voluntary recall, CAMPAIGN I.D. # R0606, that involves the crankshaft position sensor:

Quote: Nissan has determined that on some 2003 - 2004 Altima and Sentra vehicles with the 2.5 liter engine the operation of the crank angle sensor is significantly affected by variations in temperature that occur due to the unique location of the sensor in the engine. Under certain driving conditions, these variations in temperature can be large enough to cause a brief interruption in the signal output from the sensor. If the interruption in the signal from the sensor is so brief that the Electronic Control Module (ECM) logic does not have time to diagnose the condition, the engine may stop running without warning while the vehicle is driven at low speed.

Posted on Jun 29, 2010

  • 1 Answer

SOURCE: EPS warning light on on my Mitsubishi Colt (2006).

My EPS on my mitsubishi colt 2006 stopped working about 8 months now, I changed the electronic box,but it started to work for ten minutes and then stopped.I carried it by some electricians and they put the computer on it, but it is not getting through.Could someone lend some assistance!!!!!!!!!!!!!!!!!!!!!!!!1

Posted on Jul 08, 2010

smhb1
  • 146 Answers

SOURCE: crankshaft sensor for vw polo where is the

Crankshaft sensor is located on the right side of the cylinder block behind or under the starter. It is fitted into the rear crankshaft oil seal hausing

Posted on Sep 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Mitsubishi Eclipse GT 2dr Hatchback 3.8l crankshaft sensor location


It's under the timing belt cover in the one oclock position compared to the crankshaft.

Jun 23, 2017 | Mitsubishi Cars & Trucks

1 Answer

Where is the crankshaft position sensor located on the 2002 Mitsubishi Montero sport xls 3.5 truck.


Hi David, The link below is how to test the crank sensor (1997-2004 3.0l Montero, Hope this helps......CHEERS
http://easyautodiagnostics.com/mitsubishi/3.0L/crankshaft-position-sensor-test-1#3
The crankshaft position (CKP) sensor is located behind the timing belt... but testing it is done without removing the timing belt or its components. This is due to the fact that the crank sensor's connector is located on top of the engine and in plain view (next to the ignition control module). In the photo below, the orange arrow points to the location of the crankshaft position sensor connectors (photo applies to: 3.0L 1997-2004 Montero Sport).

Mar 31, 2016 | Mitsubishi Cars & Trucks

1 Answer

Where is crank sensor on mitsubishi colt


Nick, this is mostly an educated guess, Mitsubishi made so many engines, dependent and model and geography. But, MOST are located on the front of the engine(where the belt is) under or near the water pump. Access is from beneath the car. The other location, although unlikely, would be on the bell housing next to the engine. Helpful Hint>>>Sometimes and in some models, low battery voltage or a weak starter can trigger a Crankshaft Position Sensor code. before replacing any parts, recharge or replaced battery.

Nov 29, 2014 | Mitsubishi Cars & Trucks

1 Answer

Mitsubishi Colt CZ2. Fault code C1278 (valve relay stuck off). where is relay located?


Have you looked in the owner's manual for the location? It must be in the underhood fuse and relay center.

Oct 09, 2014 | 2006 Mitsubishi Colt

1 Answer

Were is the throttle position sensor


The tps is located on The throttle body

Sep 03, 2014 | 2006 Mitsubishi Colt

1 Answer

I can't locate the dip stick for the auoto oil on my coltplus 2006 ?


i doubt it has a dipstick as is what is known as a sesled unit and should only need to be checked at a major service follow this link to the colt forum for more detailed advice
ColtUK The Mitsubishi Colt Owners Club Index page

May 01, 2014 | Mitsubishi Cars & Trucks

1 Answer

Hi, i own a mitsubishi colt 06, the colour is grey, but i can't find the colour code. Please help


There's an ID plate on the top center of the firewall in the engine bay. The paint code is there.

Sep 07, 2011 | 2006 Mitsubishi Colt

1 Answer

How to make remote key for Mitsubishi colt 2006?


do you have a remote key at all?
if yes then you can take the key go to a keymaker shop and thei will be able to clone the key code and duplicate a new remote key for you.

Oct 31, 2009 | 2006 Mitsubishi Colt

1 Answer

P code


P1936 is a Clutch Switch/ Sensor Signal problem.
Hope this helps you solve the problem. 

Apr 22, 2009 | 2006 Mitsubishi Colt

2 Answers

55 plate colt


The sensor is behind the bumper reinforcement panel.

Mar 27, 2009 | 2006 Mitsubishi Colt

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

395 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...