Question about Cars & Trucks

Open Question

Astrostart remote won't start car after car battery died..unlocks and locks but no start, doesn't turn engine

Car battery died, now remote won't turn engine over..unlocks and locks the doors

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
jasperoni
  • 203 Answers

SOURCE: 2000 Mercedes ML430 Battery Change Failed

you have to resynch your remote once it looses power. the procedure is in your owner's manual. It can also be done from a scan tool but you would have to take the car to a shop. I beleive you hold the lock button and press the unlock button 5 times within 10 seconds and then put the key in the ignition but I cannot remember year for year procedures

Posted on Jun 17, 2009

Ad
rockitman187
  • 2559 Answers

SOURCE: My key fob remote will not unlock car doors but will start car

Here you go.If you can't read it I can email it to you.
c2293a3.jpg

Posted on Aug 04, 2009

alicantecoli
  • 22326 Answers

SOURCE: 2006 kia spectra. The power door locks

security ----encrypted software dealer only

Posted on Dec 03, 2009

KENNETHROSEN
  • 60 Answers

SOURCE: remote car key not working to unlock car. it does

Most likely the remote is the culprit.It sending a signal and the body control module is receiving it so that eliminates the remainder of the system.If you have two remotes then try the other one.If not, you can go to your nearest dealership and they have a remote checker.They can set the remote on it and push the buttons and it will light up if all the buttons are working on your remote.Hope this information helps,
Ken

Posted on Oct 08, 2010

  • 14036 Answers

SOURCE: replaced batery in key fob

reprogram the remote transmitter. first leave driver door open all other doors closed,key removed from the ignition switch. insert key into the ignition switch,then remove it.press lock and unlock on the vechicle door lock control switch at 1 second intervals 5 times. close and repoen drivers door.press lock and unlock on the vechicle lock control switch at 1 second intervals 5 times. insert key into ignition switch. switch ignition on and off twice to program a remote transmitter code whilst erasing the original codes or three timre to check how many remote transmitters are currently registered.remove key from the ignition switch.system should now lock and unlock.twice to indicate programming mode or one to four times,slowly to indicate number of remote transmitters registered.for the solara press and hold lock and unlock remote buttons together, press lock remote button for a second period of 1 second. system should now lock and unlock vechicle.once to confirm, twice to indicate registration has failed.if required repeat button procedure to program remaining remote transmitters.note to exit programming mode close drivers door or insert ignition key.maximum of 4 remote transmitters can be programmed.if akk failed let dealership reprogram remote transmitters.

Posted on May 18, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an Astrostart hst5224, It will star then immediately shut off. My jeep is A manual transmission


[PDF]MODEL RSS-5225 - DirectedDealers.com

www.directeddealers.com/manuals/OG/Astrostart/RSS-5225_OG-Eng.pdf
Immediately report any malfunction to the AstroStart dealer that performed the ... Always turn off the main switch when not using the remote starter for .... The startmodule will inform you of the status of door locks, the alarm and of the engine. .... If the trunk is opened for more than 5 minutes, the system switches to the.

How do you reprogram an AstroStart remote HST5224

www.answers.com > Wiki Answers > Categories > Cars & Vehicles
In order to reprogram an AstroStart HST5224 remote, you must putthe key in the ignition ... lamp) b, press and hold UNLOCK button, after 1 second key LED will flash once c, .... C. Turn the ignition to ON (Do NOT Start) then back to OFF. ... B.Immediately after letting go of the lock and unlock buttons, press the lock button by ..

Nov 24, 2015 | 2007 Jeep Wrangler Unlimited Rubicon 2...

Tip

I removed the battery and now the car won't start


'I disconnected the car battery/changed the car battery and now my car won't start'

Another common question on Fixya.
You've done nothing wrong. It's simply that the immobiliser doesn't recognise the key.

Put the key into the ignition. Turn the ignition on. Press the LOCK button twice on your remote. Wait 1 minute.

Turn the ignition off and press the UNLOCK button on the remote a couple of times. This will disarm the immobiliser.

The key should be recognised and your vehicle will start.

on Feb 19, 2016 | Cars & Trucks

1 Answer

My remote car starter from autostart on a grand am 03 won't start or locks won't work after it died for about a week then changed the batteries


Check to be sure the new battery is a good new one, they set on the shelves for some time ya know. Then make sure it goes in the correct direction.Then refer to your owners manual if it needs reprogrammed.

Feb 18, 2013 | Cars & Trucks

1 Answer

2005 Toyota Camry 4 cylinder intermittently won't start


try starting the car and while running disconnect the negative battery cable,if the car still runs turn on the head lights,if the car dies the alternator is weak. I think its weak and can charge the battery as long as the lights are off,but cant keep up when theyare on. so if drive most of the time in the day time you are ok as long as you dont have to start the car too many times. when you drive with the lights on and the engine slows to an idle like when you park the car dies. make sense?

Dec 18, 2012 | 2005 Toyota Camry LE

2 Answers

Astrostart won't start the car


You may need to reset the system.

SEQUENCE ACTIVATED BY THE PARKING BRAKE .
1. While engine is running (key in ignition switch), apply the brakes and hold the pedal down.
2. Move gearshift lever to neutral.
3. Apply the parking brake Once Twice
Note: The system can be set - at time of installation - to require that the parking brake be applied once or twice.
If set for two actuations, pause one second between the two.
4. Remove key from ignition (the system keeps the engine running).
5. Exit the vehicle.
6. Within 60 seconds, close all doors.
7. The system will stop the engine and blink the parking brakes once to confirm the sequence is valid (vehicle is
ready for a remote start command).
SEQUENCE ACTIVATED BY THE REMOTE CONTROL
1. While engine is running (key in ignition switch), apply the brakes and hold the pedal down.
2. Move gearshift lever to neutral.
3. Apply parking brake.
4. Send the start command (Model 801 & 2101 - Model 903 ).
5. Remove key from ignition (the system keeps the engine running).
6. Exit the vehicle.
7. Using the remote, send the STOP command. The system will stop the engine and parking lights will blink once
to confirm that the sequence is valid (vehicle is ready for a remote start command).
http://www.astrostart.com/Support/Guides.aspx

Nov 27, 2012 | Cars & Trucks

1 Answer

All my remotes won't unlock passenger doors, why?


this is a problem that can appear after your car battery died, cause the car didn't reset propely, so taking the battery out and putting it back in or letting your car die again would do the trick. I tried a lot of reprogramming procedured for my remote key, none of them worked, what did the trick though was simply unlocking the doors via the all door unlock button on the passenger side door, so simple.

Apr 27, 2012 | Cars & Trucks

1 Answer

Astrostart 2100 autostart will not work all the time


It would almost appear that your battery is weak. If the engine doesn't freely turn over the remote start will not work because it recognizes the problem. I would also hope that you plug in your block heater when it's really cold.

Feb 06, 2012 | Chrysler Town and Country Cars & Trucks

1 Answer

I changed the key batteries for my 1999 BMW 323i after they died. Afterwards the remote unlock and lock won't work, the car also won't start but it can turn over/on and the radio and the lights...


stick the key in the ignition, turn it to the on position, remove it within 5 seconds, then hold the unlock button down and press the lock button 3 times within 10 seconds and release both buttons. The doors should lock/unlock to give you confirmation and your key should work.

Jul 05, 2011 | 1999 BMW 323 Series

2 Answers

HELP please!! My daughter has a 96 sebring convertible and today she put her key in the door to unlock it and the alarm started going off. It wont stop, have disconnected the positive and negative battery...


Just a quick note once you hook the battery back up try locking it and unlocking it from the drivers door, if that fails you might try the passenger door. I know on some chrysler products you have to lock and lock again to arm and unlock to disarm. I hope this helps.
Thanks,
Joey

Sep 05, 2010 | 1998 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

745 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15427 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...